參數資料
型號: OP193FSZ-REEL7
廠商: Analog Devices Inc
文件頁數: 4/16頁
文件大?。?/td> 0K
描述: IC OPAMP GP 35KHZ PREC 8SOIC
設計資源: 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145)
標準包裝: 1,000
放大器類型: 通用
電路數: 1
輸出類型: 滿擺幅
轉換速率: 0.015 V/µs
增益帶寬積: 35kHz
電流 - 輸入偏壓: 20nA
電壓 - 輸入偏移: 150µV
電流 - 電源: 30µA
電流 - 輸出 / 通道: 25mA
電壓 - 電源,單路/雙路(±): 1.7 V ~ 36 V,±0.85 V ~ 18 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 8-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 8-SOIC
包裝: 帶卷 (TR)
REV. B
OP193/OP293/OP493
–12–
A Single-Supply Instrumentation Amplifier
Designing a true single-supply instrumentation amplifier with
zero-input and zero-output operation requires special care.
The traditional configuration, shown in Figure 9, depends upon
amplifier A1’s output being at 0 V when the applied common-
mode input voltage is at 0 V. Any error at the output is multiplied
by the gain of A2. In addition, current flows through resistor R3
as A2’s output voltage increases. A1’s output must remain at 0 V
while sinking the current through R3, or a gain error will result.
With a maximum output voltage of 4 V, the current through R3
is only 2
A, but this will still produce an appreciable error.
5V
V+
V–
5V
V+
V–
VOUT
R4
1.98M
R3
20k
R2
1.98M
R1
20k
ISINK
–IN
+IN
1/2 OP293
A2
1/2 OP293
A1
Figure 9. A Conventional Instrumentation Amplifier
One solution to this problem is to use a pull-down resistor. For
example, if R3 = 20 k
, then the pull-down resistor must be
less than 400
. However, the pull-down resistor appears as a
fixed load when a common-mode voltage is applied. With a 4 V
common-mode voltage, the additional load current will be 10 mA,
which is unacceptable in a low power application.
Figure 10 shows a better solution. A1’s sink current is provided
by a pair of N-channel FET transistors, configured as a current
mirror. With the values shown, sink current of Q2 is about
340
A. Thus, with a common-mode voltage of 4 V, the addi-
tional load current is limited to 340
A versus 10 mA with a
400
resistor.
5V
V+
V–
5V
V+
V–
VOUT
+IN
1/2 OP293
A2
R4
1.98M
R3
20k
R2
1.98M
R1
20k
–IN
1/2 OP293
A1
5V
10k
Q1
Q2
VN2222
Figure 10. An Improved Single-Supply, 0 VIN, 0 VOUT
Instrumentation Amplifier
A Low-Power, Temperature to 4–20 mA Transmitter
A simple temperature to 4–20 mA transmitter is shown in Fig-
ure 11. After calibration, this transmitter is accurate to
±0.5°C
over the –50
°C to +150°C temperature range. The transmitter
operates from 8 V to 40 V with supply rejection better than
3 ppm/V. One half of the OP293 is used to buffer the VTEMP
pin, while the other half regulates the output current to satisfy
the current summation at its noninverting input:
I
VR6
R7
R2
R10
V
R2
R6
R7
R2
R10
OUT
TEMP
SET
+
×+
×
++
×
()
The change in output current with temperature is the derivative
of the transfer function:
I
T
V
T
R6
R7
R2
R10
OUT
TEMP
=
+
×
()
SPAN TRIM
8
4
8V TO 40V
V+
1/2 OP293
R4
20k
R9
100k
R2
1k
1/2 OP293
VTEMP
2N1711
1
2
3
R1 10k
2
6
3
4
REF-43BZ
VIN
VOUT
VTEMP
GND
R5
5k
R3
100k
6
5
ZERO
TRIM
VSET
7
R6
3k
R7
5k
R8
1k
1N4002
R10
100
1%, 1/2 W
RLOAD
IOUT
ALL RESISTORS 1/4W, 5% UNLESS OTHERWISE NOTED
Figure 11. Temperature to 4–20 mA Transmitter
相關PDF資料
PDF描述
2070.0021.11 FUSE OSU 250V 3.15A
AD8034ARZ-REEL7 IC OPAMP VF R-R DUAL LN LP 8SOIC
0459844313 CONN RCPT R/A 4PWR 12SGL 1.57MM
LT1620CMS8#PBF IC AMP R-R CURRENT SENSE 8-MSOP
0459844312 CONN RCPT R/A 4PWR 12SGL 2.36MM
相關代理商/技術參數
參數描述
OP193FSZ-REEL71 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision, Micropower Operational Amplifiers
OP193GBC 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision, Micropower Operational Amplifiers
OP196 制造商:AD 制造商全稱:Analog Devices 功能描述:Micropower, Rail-to-Rail Input and Output Operational Amplifiers
OP196_02 制造商:AD 制造商全稱:Analog Devices 功能描述:Micropower, Rail-to-Rail Input and Output Operational Amplifiers
OP196496 制造商:未知廠家 制造商全稱:未知廠家 功能描述: