- 您現在的位置：買賣IC網 > PDF目錄5724 > OP262TRZ-EP (Analog Devices Inc)IC OPAMP GP R-R 15MHZ DUAL 8SOIC PDF資料下載
參數資料
| 型號： | OP262TRZ-EP |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP GP R-R 15MHZ DUAL 8SOIC |
| 標準包裝： | 98 |
| 放大器類型： | 通用 |
| 電路數： | 2 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 13 V/µs |
| 增益帶寬積： | 15MHz |
| 電流 - 輸入偏壓： | 260nA |
| 電壓 - 輸入偏移： | 25µV |
| 電流 - 電源： | 650µA |
| 電流 - 輸出 / 通道： | 30mA |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 12 V，±1.5 V ~ 6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 管件 |
OP162/OP262/OP462
Data Sheet
Rev. H | Page 16 of 20
APPLICATIONS CIRCUITS
SINGLE-SUPPLY STEREO HEADPHONE DRIVER
Figure 43 shows a stereo headphone output amplifier that can
operate from a single 5 V supply. The reference voltage is
derived by dividing the supply voltage down with two 100 k
resistors. A 10 F capacitor prevents power supply noise from
contaminating the audio signal and establishes an ac ground for
the volume control potentiometers.
The audio signal is ac-coupled to each noninverting input
through a 10 F capacitor. The gain of the amplifier is con-
trolled by the feedback resistors and is (R2/R1) + 1. For this
example, the gain is 6. By removing R1, the amplifier would
have unity gain. To short-circuit protect the output of the
device, a 169 resistor is placed at the output in the feedback
network. This prevents any damage to the device if the head-
phone output becomes shorted. A 270 F capacitor is used at
the output to couple the amplifier to the headphone. This value
is much larger than that used for the input because of the low
impedance of headphones, which can range from 32 to 600
or more.
Figure 43. Headphone Output Amplifier
INSTRUMENTATION AMPLIFIER
Because of their high speed, low offset voltages, and low noise
characteristics, the OP162/OP262/OP462 can be used in a wide
variety of high speed applications, including precision instru-
mentation amplifiers. Figure 44 shows an example of such an
application.
Figure 44. High Speed Instrumentation Amplifier
The differential gain of the circuit is determined by RG, where
G
DIFF
R
A
2
1+
=
with the RG resistor value in k. Removing RG sets the circuit
gain to unity.
The fourth op amp, OP462-D, is optional and is used to
improve CMRR by reducing any input capacitance to the
amplifier. By shielding the input signal leads and driving the
shield with the common-mode voltage, input capacitance is
eliminated at common-mode voltages. This voltage is derived
from the midpoint of the outputs of OP462-A and OP462-B by
using two 10 k resistors followed by OP462-D as a unity-gain
buffer.
It is important to use 1% or better tolerance components for the
2 k resistors, as the common-mode rejection is dependent on
their ratios being exact. A potentiometer should also be connected
in series with the OP462-C noninverting input resistor to ground
to optimize common-mode rejection.
The circuit in Figure 44 was implemented to test its settling
time. The instrumentation amp was powered with 5 V, so the
input step voltage went from 5 V to +4 V to keep the OP462
within its input range. Therefore, the 0.05% settling range is
when the output is within 4.5 mV. Figure 45 shows the positive
slope settling time to be 1.8 s, and Figure 46 shows a settling
time of 3.9 s for the negative slope.
OP262-A
5V
169
270
F
47k
L VOLUME
CONTROL
R1 = 10k
10
F
10
F
10k
5V
100k
10
F
100k
R2 = 50k
LEFT IN
OP262-B
5V
169
270
F
47k
HEADPHONE
RIGHT
HEADPHONE
LEFT
10k
R VOLUME
CONTROL
10
F
RIGHT IN
R2 = 50k
10
F
R1 = 10k
00288-046
OP462-A
OP462-B
OP462-C
OP462-D
–VIN
+VIN
1k
10k
2k
1.9k
200
10 TURN
(OPTIONAL)
OUTPUT
RG
1k
10k
2k
2k
00288-047
相關PDF資料 |
PDF描述 |
|---|---|
| AD603AR-REEL7 | IC AMP VGA 90MHZ LN 50MA 8SOIC |
| PFC-W0402LF-03-1002-B-4155 | RES PREC 10K OHM 50MW .1% 0402 |
| RNCF0603BTE11K1 | RES 11.1K OHM 1/16W 0.1% 0603 |
| S-2 0.500 OHM 1% | RES .5 OHM 1W 1% WW SMD |
| 961118-6300-AR-TP | CONN HEADER VERT 18POS GOLD SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OP262TRZ-EP-R7 | 功能描述:IC OPAMP GP R-R 15MHZ DUAL 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:13 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:65pA 電壓 - 輸入偏移:3000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| OP265 | 制造商:OPTEK 制造商全稱:OPTEK 功能描述:GAAIAS PLASTIC INFRARED EMITTING DIODE |
| OP265_06 | 制造商:OPTEK 制造商全稱:OPTEK 功能描述:Plastic Infrared Emitting Diode |
| OP265A | 功能描述:標準LED-通孔 High Intensity 890nm RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
| OP265AA | 功能描述:標準LED-通孔 Infrared 850nm RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。