參數資料
型號： OP270GS
廠商： Analog Devices Inc
文件頁數： 6/20頁
文件大小： 0K
描述： IC OPAMP GP 5MHZ DUAL LN 16SOIC
標準包裝： 47
放大器類型： 通用
電路數： 2
轉換速率： 2.4 V/µs
增益帶寬積： 5MHz
電流 - 輸入偏壓： 15nA
電壓 - 輸入偏移： 50µV
電流 - 電源： 4mA
電壓 - 電源，單路/雙路(±)： ±4.5 V ~ 18 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 16-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 16-SOIC W
包裝： 管件
OP270
Rev. E | Page 14 of 20
NOISE MEASUREMENTS
Peak-to-Peak Voltage Noise
The circuit of Figure 35 is a test setup for measuring peak-to-
peak voltage noise. To measure the 200 nV peak-to-peak noise
specification of the OP270 in the 0.1 Hz to 10 Hz range, the
following precautions must be observed:
The device has to be warmed up for at least five minutes.
As shown in the warm-up drift curve (see Figure 8), the
offset voltage typically changes 2 μV due to increasing chip
temperature after power-up. In the 10 sec measurement
interval, these temperature-induced effects can exceed tens
of nanovolts.
For similar reasons, the device has to be well shielded from
air currents. Shielding also minimizes thermocouple effects.
Sudden motion in the vicinity of the device can also feed
through to increase the observed noise.
The test time to measure noise of 0.1 Hz to 10 Hz should
not exceed 10 sec. As shown in the noise-tester frequency
response curve of Figure 36, the 0.1 Hz corner is defined by
only one pole. The test time of 10 sec acts as an additional
pole to eliminate noise contribution from the frequency
band below 0.1 Hz.
A noise voltage density test is recommended when measuring
noise on several units. A 10 Hz noise voltage density mea-
surement correlates well with a 0.1 Hz to 10 Hz peak-to-peak
noise reading because both results are determined by the
white noise and the location of the 1/f corner frequency.
Power should be supplied to the test circuit by well bypassed
low noise supplies, such as batteries. Such supplies will min-
imize output noise introduced via the amplifier supply pins.
00
35
2-
0
37
100
60
80
0
20
40
GA
IN
(
d
B
)
FREQUENCY (Hz)
0.01
0.1
1
10
100
Figure 36. 0.1 Hz to 10 Hz Peak-to-Peak Voltage Noise
Test Circuit Frequency Response
Noise Measurement—Noise Voltage Density
The circuit of Figure 37 shows a quick and reliable method for
measuring the noise voltage density of dual op amps. The first
amplifier is in unity gain, with the final amplifier in a noninverting
gain of 101. Because the noise voltages of the amplifiers are
uncorrelated, they add in rms to yield
( ) ( )
(
)2
2
101
nB
nA
OUT
e
+
=
The OP270 is a monolithic device with two identical amplifiers.
Therefore, the noise voltage densities of the amplifiers match,
giving
(
) ( )
n
OUT
e
2
101
2
101
2
=
00
32
5-
0
38
eOUT (nV/√Hz) ≈ 101 (√2en)
VS = ±15V
TO SPECTRUM ANALYZER
eOUT
R1
100
R2
10k
1/2
OP270
1/2
OP270
Figure 37. Noise Voltage Density Test Circuit
Noise Measurement—Current Noise Density
The test circuit shown in Figure 38 can be used to measure current
noise density. The formula relating the voltage output to the current
noise density is
()
S
nOUT
n
R
Hz
nV
G
e
i
2
/
40
=
where:
G is a gain of 10,000.
RS = 100 kΩ source resistance.
00
32
5-
0
39
OP270
DUT
R1
5
R2
100k
R3
1.24k
OP27E
R5
8.06k
R4
200
enOUT
GAIN = 10,000
VS = ±15V
TO SPECTRUM ANALYZER
Figure 38. Current Noise Density Test Circuit
相關PDF資料
PDF描述
OP279GS IC OPAMP GP R-R 5MHZ DUAL 8SOIC
OP27GS IC OPAMP GP 8MHZ LN PREC 8SOIC
OP282GS IC OPAMP JFET 4MHZ DUAL LP 8SOIC
OP285GSZ-REEL IC OPAMP GP 9MHZ DUAL PREC 8SOIC
OP291GSZ-REEL7 IC OPAMP GP R-R 3MHZ DUAL 8SOIC
相關代理商/技術參數
參數描述
OP-270GS 制造商:AD 制造商全稱:Analog Devices 功能描述:DUAL VERY LOW NOISE PRECISION OPERATIONAL AMPLIFIER
OP270GS-REEL 功能描述:IC OPAMP GP 5MHZ DUAL LN 16SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT
OP270GSZ 功能描述:IC OPAMP GP 5MHZ DUAL LN 16SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR
OP270GSZ2 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Very Low Noise Precision Operational Amplifier
OP270GSZ-REEL 功能描述:IC OPAMP GP 5MHZ DUAL LN 16SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*