參數資料
型號: OP4177ARZ-REEL
廠商: Analog Devices Inc
文件頁數: 10/24頁
文件大?。?/td> 0K
描述: IC OPAMP GP 1.3MHZ QUAD 14SOIC
標準包裝: 2,500
放大器類型: 通用
電路數: 4
轉換速率: 0.7 V/µs
增益帶寬積: 1.3MHz
電流 - 輸入偏壓: 500pA
電壓 - 輸入偏移: 15µV
電流 - 電源: 400µA
電流 - 輸出 / 通道: 10mA
電壓 - 電源,單路/雙路(±): 5 V ~ 36 V,±2.5 V ~ 18 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 14-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 14-SOIC
包裝: 帶卷 (TR)
OP1177/OP2177/OP4177
Rev. G | Page 18 of 24
PROPER BOARD LAYOUT
The OPx177 is a high precision device. To ensure optimum
performance at the PCB level, care must be taken in the design
of the board layout.
To avoid leakage currents, the surface of the board should be
kept clean and free of moisture. Coating the surface creates a
barrier to moisture accumulation and helps reduce parasitic
resistance on the board.
Keeping supply traces short and properly bypassing the power
supplies minimizes power supply disturbances due to output
current variation, such as when driving an ac signal into a heavy
load. Bypass capacitors should be connected as closely as possible
to the device supply pins. Stray capacitances are a concern at the
outputs and the inputs of the amplifier. It is recommended that
signal traces be kept at least 5 mm from supply lines to
minimize coupling.
A variation in temperature across the PCB can cause a mismatch in
the Seebeck voltages at solder joints and other points where dissi-
milar metals are in contact, resulting in thermal voltage errors. To
minimize these thermocouple effects, orient resistors so heat
sources warm both ends equally. Input signal paths should contain
matching numbers and types of components, where possible to
match the number and type of thermocouple junctions. For
example, dummy components such as zero value resistors can
be used to match real resistors in the opposite input path.
Matching components should be located in close proximity and
should be oriented in the same manner. Ensure leads are of equal
length so that thermal conduction is in equilibrium. Keep heat
sources on the PCB as far away from amplifier input circuitry as
is practical.
The use of a ground plane is highly recommended. A ground
plane reduces EMI noise and also helps to maintain a constant
temperature across the circuit board.
DIFFERENCE AMPLIFIERS
Difference amplifiers are used in high accuracy circuits to improve
the common-mode rejection ratio (CMRR).
R1
V1
V2
R3 = R1
R4 = R1
OP1177
2
3
=
R4
R3
R2
R1
R2
100k
VOUT
02
62
7-
06
3
6
7
4
V+
V–
Figure 63. Difference Amplifier
In the single instrumentation amplifier (see Figure 63), where
R1
R2
R3
R4 =
()
1
2
O
V
R1
R2
V
=
a mismatch between the ratio R2/R1 and R4/R3 causes the
common-mode rejection ratio to be reduced.
To better understand this effect, consider that, by definition,
CM
DM
A
CMRR =
where ADM is the differential gain and ACM is the common-
mode gain.
CM
O
CM
DIFF
O
DM
V
A
V
A
and
=
()
2
1
CM
2
1
DIFF
V
+
=
=
2
1
and
For this circuit to act as a difference amplifier, its output must
be proportional to the differential input signal.
From Figure 63,
2
1
O
V
R4
R3
R1
R2
V
R1
R2
V
1
+
+
+
=
Arranging terms and combining the previous equations yields
R2R3
R4R1
R4R2
R3R2
R4R1
CMRR
2
+
=
(1)
The sensitivity of CMRR with respect to the R1 is obtained by
taking the derivative of CMRR, in Equation 1, with respect to R1.
+
δ
=
δ
R2R3
R1R4
R2R3
R2R4
R2R3
R1R4
R1
CMRR
2
()
R1R4
R2R3
R1
CMRR
2
1
=
δ
Assuming that
R1 ≈ R2 ≈ R3 ≈ R4 ≈ R
and
R(1 δ) < R1, R2, R3, R4 < R(1 + δ)
the worst-case CMRR error arises when
R1 = R4 = R(1 + δ) and R2 = R3 = R(1 δ)
相關PDF資料
PDF描述
FTS-148-01-L-DV CONN HEADER 96POS DUAL .05" SMD
77313-102-24LF CONN HEADER .100 DUAL STR 24POS
170M3508 FUSE 40A 690V 1GN/50
TMM-134-01-S-D CONN HEADER 68POS DUAL 2MM T/H
2035-35-B SURGE ARRESTOR GDT 350V
相關代理商/技術參數
參數描述
OP4177ARZ-REEL1 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Low Noise, Low Input Bias Current Operational Amplifiers
OP4177ARZ-REEL7 功能描述:IC OPAMP GP 1.3MHZ QUAD 14SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:73 系列:Over-The-Top® 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.07 V/µs 增益帶寬積:200kHz -3db帶寬:- 電流 - 輸入偏壓:1nA 電壓 - 輸入偏移:285µV 電流 - 電源:50µA 電流 - 輸出 / 通道:25mA 電壓 - 電源,單路/雙路(±):2 V ~ 44 V,±1 V ~ 22 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WFDFN 裸露焊盤 供應商設備封裝:16-DFN-EP(5x3) 包裝:管件
OP4177ARZ-REEL71 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Low Noise, Low Input Bias Current Operational Amplifiers
OP41AJ 制造商:AD 制造商全稱:Analog Devices 功能描述:Low-Bias-Current, High-Stability JFET Operational Amplifier
OP-41AJ 制造商:AD 制造商全稱:Analog Devices 功能描述:LOW-BIAS-CURRENT, HIGH-STABILITY JFET OPERATIONAL AMPLIFIER