- 您現在的位置：買賣IC網 > PDF目錄383692 > OPA705UA Low-Cost, CMOS, Rail-to-Rail, I/O OPERATIONAL AMPLIFIERS PDF資料下載
參數資料
| 型號： | OPA705UA |
| 英文描述： | Low-Cost, CMOS, Rail-to-Rail, I/O OPERATIONAL AMPLIFIERS |
| 中文描述： | 低成本的CMOS軌到軌輸入/輸出運算放大器 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 280K |
| 代理商： | OPA705UA |
OPA705, 2705, 4705
SBOS182A
9
RAIL-TO-RAIL OUTPUT
A class AB output stage with common-source transistors is
used to achieve rail-to-rail output. This output stage is
capable of driving 1k
loads connected to any point be-
tween V+ and ground. For light resistive loads (> 100k
),
the output voltage can swing to 40mV from the supply rail.
With moderate resistive loads (20k
), the output can swing
to within 75mV from the supply rails while maintaining high
open-loop gain (see the typical performance curve “Output
Voltage Swing vs Output Current”).
CAPACITIVE LOAD AND STABILITY
The OPA705 series op amps can drive up to 1000pF pure
capacitive load. Increasing the gain enhances the amplifier’s
ability to drive greater capacitive loads (see the typical
performance curve “Small Signal Overshoot vs Capacitive
Load”).
One method of improving capacitive load drive in the unity-
gain configuration is to insert a 10
to 20
resistor inside the
feedback loop, as shown in Figure 5. This reduces ringing
with large capacitive loads while maintaining DC accuracy.
FIGURE 5. Series Resistor in Unity-Gain Buffer Configura-
tion Improves Capacitive Load Drive.
INPUT VOLTAGE
Device inputs are protected by ESD diodes that will conduct
if the input voltages exceed the power supplies by more than
approximately 300mV. Momentary voltages greater than
300mV beyond the power supply can be tolerated if the
current is limited to 10mA. This is easily accomplished with
an input resistor, as shown in Figure 3. Many input signals
are inherently current-limited to less than 10mA; therefore,
a limiting resistor is not always required. The OPA705
features no phase inversion when the inputs extend beyond
supplies if the input current is limited, as seen in Figure 4.
FIGURE 4. OPA705—No Phase Inversion with Inputs
Greater than the Power-Supply Voltage.
FIGURE 3. Input Current Protection for Voltages Exceeding
the Supply Voltage.
2
V
S
=
±
5.0V, V
IN
= 11Vp-p
20
μ
s/div
APPLICATION CIRCUITS
The OPA705 series op amps are optimized for driving
medium-speed sampling data converters. Figure 6 shows the
OPA2705 in a dual-supply buffered reference configuration
for the DAC7644. The DAC7644 is a 16-bit, low-power,
quad-voltage output converter. Small size makes the combi-
nation ideal for automatic test equipment, data acquisition
systems, and other low-power space-limited applications.
R
OPA705
10mA max
+V
V
–
V
IN
V
OUT
I
OVERLOAD
R
S
20
OPA705
C
L
R
L
V
IN
V
OUT
相關PDF資料 |
PDF描述 |
|---|---|
| OPA4705EA | Low-Cost, CMOS, Rail-to-Rail, I/O OPERATIONAL AMPLIFIERS |
| OPA4705UA | Low-Cost, CMOS, Rail-to-Rail, I/O OPERATIONAL AMPLIFIERS |
| OPA511 | High Current?High Power OPERATIONAL AMPLIFIER |
| OPA511AM | High Current?High Power OPERATIONAL AMPLIFIER |
| OPA551 | High-Voltage. High-Current Operational Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OPA705UA/2K5 | 制造商:BB 制造商全稱:BB 功能描述:Low-Cost, CMOS, Rail-to-Rail, I/O OPERATIONAL AMPLIFIERS |
| OPA705UAG4 | 功能描述:運算放大器 - 運放 12V Low Cost CMOS Rail-to-Rail I/O RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| OPA708 | 制造商:OPTEK 制造商全稱:OPTEK 功能描述:REFLECTIVE OBJECT SENSORS |
| OPA725 | 制造商:BB 制造商全稱:BB 功能描述:Very Low Noise, High-Speed, 12V CMOS Operational Amplifier |
| OPA725AID | 功能描述:運算放大器 - 運放 Very Low-Noise High Speed 12V CMOS RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。