參數資料
型號: P1500ECRP1
英文描述: SIDAC|180V V(BO) MAX|800MA I(S)|TO-92VAR
中文描述: SIDAC的| 180V五(公報)最大| 800mA的我(縣)|對92VAR
文件頁數: 86/161頁
文件大?。?/td> 986K
代理商: P1500ECRP1
ITU-T K.20 and K.21
SIDACtor
Data Book
4 - 12
Teccor Electronics
(972) 580-7777
External Protectors
For equipment being tested to the exposed level, it is standard practice for external
line protectors (typically gas tubes) to be used in order to handle the large surge
currents generated during K.20 and K.21 qualification. Realizing that these protectors
can affect the characteristics of the EUT, it is important that the protectors used be
agreed upon by the principal parties involved (the equipment supplier and testing
administrator). Once agreed upon, the protectors should be used when primary
protection is specified, and allowance should be given for a new set of protectors after
the completion of each test sequence.
Note:
An alternative to using external protectors is for the test administrator to simulate the
conditions expected (as if the external protectors were used) by modifying the surges
found in K.20 and K.21.
Equipment Boundaries
Because of the numerous types of equipment, during K.20 and K.21 testing ITU-T
looks at each EUT as a
black box
with three terminals (A, B, and E). The applicant is
expected to define the boundaries of this
black box
, and in doing so, should be aware
that any protective device within these boundaries is considered an unchangeable part
of that piece of equipment.
Permitted Malfunction or Damage
During K.20 and K.21 qualification, ITU-T recognizes two levels of malfunction or
damage to the EUT:
Level A states that equipment withstands the test without damage or disturbance
and operates properly after the test. If specifically permitted, the administration
may accept the opening of the fuse.
Level B states that a fire hazard does not occur in the equipment as a result of the
test, and that any permanent damage or malfunction is confined to a small number
of external line interface circuits (as defined by the test administrator).
The acceptable level of malfunction for each test is specified under Acceptance
Criteria.
相關PDF資料
PDF描述
P1500ECRP2 MCU CMOS 18 LD 4MHZ .5K FLASH, 0C to +70C, 18-PDIP, TUBE
P1500SARP MCU CMOS 18 LD 4MHZ .5K FLASH, -40C to +85C, 18-SOIC 300mil, TUBE
P1500SBRP MCU CMOS 18 LD 10MHZ .5K FLASH, -40C to +85C, 18-PDIP, TUBE
P1500SCRP MCU CMOS 18 LD LOW PWR, 0C to +70C, 18-SOIC 300mil, TUBE
P1602ABRP MCU CMOS 18 LD LOW PWR, -40C to +85C, 18-PDIP, TUBE
相關代理商/技術參數
參數描述
P1500ECRP2 功能描述:硅對稱二端開關元件 500A 140V RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流(在 VDRM IDRM 下): 保持電流(Ih 最大值):50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1500G_LRP 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:Teccor㈢ brand Protection Thyristors
P1500GALRP 功能描述:硅對稱二端開關元件 140V 50A DO15 SIDACtor Bi RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流(在 VDRM IDRM 下): 保持電流(Ih 最大值):50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1500GBLRP 功能描述:硅對稱二端開關元件 140V 80A DO15 SIDACtor Bi RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流(在 VDRM IDRM 下): 保持電流(Ih 最大值):50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1500GTL 制造商:SEMIKRON 制造商全稱:Semikron International 功能描述:Standard silicon rectifier diodes