- 您現在的位置：買賣IC網 > PDF目錄367627 > P1800SBRP SIDAC|220V V(BO) MAX|800MA I(S)|DO-214AA PDF資料下載
參數資料
| 型號： | P1800SBRP |
| 英文描述： | SIDAC|220V V(BO) MAX|800MA I(S)|DO-214AA |
| 中文描述： | SIDAC的| 220五（公報）最大| 800mA的我（縣）|的DO - 214AA |
| 文件頁數： | 85/161頁 |
| 文件大?。?/td> | 986K |
| 代理商： | P1800SBRP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁當前第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁
SIDACtor
Data Book
ITU-T K.20 and K.21
Teccor Electronics
(972) 580-7777
4 - 11
R
R
5 67!'67!"
Overview
Although the ITU does not have the authority to legislate that organizations follow their
recommendations, their standards are recognized in many places throughout Europe
and the Far East.
ITU-T, the Telecommunication Standardization Sector of the International
Telecommunication Union, has developed fundamental testing methods that have
been established to cover various environmental conditions to help predict the
survivability of network and customer based switching equipment. The conditions
covered are surges due to lightning strikes on or near twisted pair and or plant
equipment (this does not include a direct strike), short term induction of AC voltage
from adjacent power lines or railway systems, and direct contact between
telecommunication lines and power lines (this is often referred to as AC power cross).
The two applicable ITU-T standards for most telecommunications equipment to be
connected to the network are ITU-T K.20 which is primarily for switching equipment
powered by the central office, and ITU-T K.21 which focuses on customer premise
equipment. However, for complex subscriber equipment, test administrators may
choose either K.20 or K.21, depending on which they feel is most appropriate.
Note:
Both standards are meant to address equipment reliability versus equipment safety, so
for specific concerns regarding equipment safety, national standards should be
researched and followed for each country where the equipment is intended to be used.
ITU-T K.20
Covers telephone exchanges and switching centers. Equipment submitted under K.20
must meet one of two levels. The lower level is intended for equipment that is used in
an unexposed environment where over-voltages and over-currents are expected to be
small and external protectors omitted (similar to the intra-building scenario found in
Bellcore 1089). The higher level is intended to cover more exposed environments
where external line protectors are used. Guidelines for determining which environment
the equipment under test (EUT) falls under can be found in ITU-T K.11, but it should be
noted that the final authority rests with the test administrator. That being the case, and
since equipment satisfying the requirements of the exposed criteria can also meet the
requirements satisfying the non-exposed requirements, only the exposed level
requirements are addressed in this document.
ITU-T K.21
Addresses desk-borne equipment that may or may not be used in an exposed
environment. It is assumed that external line protectors are employed for equipment
used in exposed areas and not used for unexposed environments. With this in mind,
K.21 is conducted with and without external line protectors.
相關PDF資料 |
PDF描述 |
|---|---|
| P1800SCRP | SIDAC|220V V(BO) MAX|800MA I(S)|DO-214AA |
| P1803AA | SIDAC|210V V(BO) MAX|800MA I(S)|TO-220VAR |
| P1803AARP | SIDAC|210V V(BO) MAX|800MA I(S)|TO-220VAR |
| P1803AB | SIDAC|210V V(BO) MAX|800MA I(S)|TO-220VAR |
| P1803ABRP | SIDAC|210V V(BO) MAX|800MA I(S)|TO-220VAR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P1800SC | 功能描述:硅對稱二端開關元件 500A 170V RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA |
| P1800SCL | 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:gas plasma arresters-package dimensions/specifications |
| P1800SCLRP | 功能描述:硅對稱二端開關元件 500A 170V RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA |
| P1800SCMC | 功能描述:硅對稱二端開關元件 500A 170V RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA |
| P1800SCMCL | 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:MicroCapacitance (MC) SC SIDACtor㈢ Device |
發布緊急采購，3分鐘左右您將得到回復。