參數資料
型號: P1803AB
英文描述: SIDAC|210V V(BO) MAX|800MA I(S)|TO-220VAR
中文描述: SIDAC的|高達210V五(公報)最大| 800mA的我(縣)|對220VAR
文件頁數: 59/161頁
文件大?。?/td> 986K
代理商: P1803AB
SIDACtor
Data Book
Analog Line Cards
Teccor Electronics
(972) 580-7777
3 - 19
R
On-Hook (Relay) Protection
On-hook protection is accomplished by choosing a SIDACtor that meets the following
criteria to ensure proper coordination between the ring voltage and the maximum
voltage rating of the relay to be protected.
V
DRM
>V
BATT
+V
RING
V
S
V
Relay Breakdown
This criterion is typically accomplished using two P2600S
_
(where _ denotes the surge
current rating) SIDACtors connected from TIP to GND and RING to GND. However
those who choose to use relays such as Lucent
s LCAS (Line Card Access Switch)
should consider the P1200S
_
from TIP to GND and the P2000S
_
from RING to GND.
Off-Hook (SLIC) Protection
Off-hook protection is accomplished by choosing a SIDACtor that meets the following
criteria to ensure proper coordination between the supply voltage (V
REF
) and the
maximum voltage rating of the SLIC to be protected.
V
DRM
>V
REF
V
S
V
SLIC Breakdown
This criterion can be accomplished a variety of different ways. For applications that
use an external ring generator and a fixed battery voltage, two P0641S_ (or P0721S
_
depending on the value of V
REF
) SIDACtors are used; one TIP to GND, one RING to
GND. For applications that use a ring generating SLIC such as AMD
s Am79R79, the
P11xx0C
_
can be used.
I
PP
Selection
To ensure the proper surge current rating of the SIDACtor is selected, the I
PP
of the
SIDACtor must be greater than or equal to the maximum available surge current
(I
PK(available)
) of the applicable regulatory requirements. The maximum available surge
current is calculated by dividing the peak surge voltage supplied by the voltage
generator (V
PK
) by the total circuit resistance (R
TOTAL
). The total circuit resistance is
determined by adding the source resistance (R
S
) of the surge generator to the series
resistance that is in front of the SIDACtor on both TIP and RING (R
TIP
and R
RING
).
I
PP
I
PK(available)
I
PK(available)
=V
PK
/R
TOTAL
For metallic surges:
R
TOTAL
=R
S
+R
TIP
+R
RING
For longitudinal surges:
R
TOTAL
=R
S
+R
TIP
R
TOTAL
=R
S
+R
RING
相關PDF資料
PDF描述
P1803ABRP SIDAC|210V V(BO) MAX|800MA I(S)|TO-220VAR
P1803AC SIDAC|210V V(BO) MAX|800MA I(S)|TO-220VAR
P1803ACRP SIDAC|210V V(BO) MAX|800MA I(S)|TO-220VAR
P2200AA61RP 16-pin, 1.75KB, Flash, 72B RAM, 2x Comparator, 8HMz internal osc,Hi Volt Support, -40C to +85C, 14-PDIP, TUBE
P2202AA 16 PIN, 1.75KB FLASH, 64B RAM, 6 I/O, 8MHZ INTERNAL OSCILLATOR, -40C to +125C, 16-QFN, T/R
相關代理商/技術參數
參數描述
P1803AB60 功能描述:硅對稱二端開關元件 3Chp 150V 100A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流(在 VDRM IDRM 下): 保持電流(Ih 最大值):50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1803ABL 功能描述:硅對稱二端開關元件 3Chp 150V 100A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流(在 VDRM IDRM 下): 保持電流(Ih 最大值):50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1803ABL60 功能描述:硅對稱二端開關元件 3Chp 150V 100A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流(在 VDRM IDRM 下): 保持電流(Ih 最大值):50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1803ABLRP 功能描述:硅對稱二端開關元件 3Chp 150V 100A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流(在 VDRM IDRM 下): 保持電流(Ih 最大值):50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P1803ABLXX 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:The series provides a single port through-hole solution that enables voice