參數資料
型號： P3100ECRP2
英文描述： SIDAC|350V V(BO) MAX|800MA I(S)|TO-92VAR
中文描述： SIDAC的| 350V五（公報）最大| 800mA的我（縣）|對92VAR
文件頁數： 130/161頁
文件大?。?/td> 986K
代理商： P3100ECRP2
PCB Layout
SIDACtor
Data Book
5 - 14
Teccor Electronics
(972) 580-7777
The minimum width and thickness of conductors on a PCB is determined primarily by
the current-carrying capacity required. This current carrying capacity is limited by the
allowable temperature rise of the etched copper conductor. An adjacent ground or
power layer can significantly reduce this temperature rise. A single ground plane can
generally raise the allowed current by 50 percent. An easy approximation can be
generated by starting with Figure 5-4 to calculate the conductor cross sectional area
required. Once this has been done, Figure 5-5 converts the cross sectional area to the
required conductor width dependent on the copper foil thickness of the trace.
Figure 5-5 Conductor Width vs. Area
Trace Separation
Because Tip and Ring traces are subjected to transient conditions, they should be
routed towards the edge of the PCB away from sensitive areas, and should maintain a
minimum separation of 2.5mm between themselves and other traces. A good rule of
thumb for separation of non-coated top layer traces is to maintain spacing equal to
.010mm per volt.
Grounding
Although often overlooked, grounding is a very important design consideration when
laying out a protection interface circuit. To optimize its effectiveness, several things
should be considered.
The first is that a large copper plane should be provided using a grid pattern for the
ground reference point.
Next, it should be decided if a single point or a multi point grounding scheme is to be
used. A single-point (also called centralized) grounding scheme is used for circuit
dimensions smaller than one-tenth of a wavelength (
λ
= 300,000/F
kHz
) and a multi
point (also called distributed) grounding scheme is used for circuit trace lengths
0
.350
.300
.250
.030
.050
.070
.100
.150
.200
.010
.020
.005
.001
0
1
10
20
100 150
300
400
500
600
700
Conductor Cross-Section Area (sq mils)
5
30 50 70
200
250
C
0
"
7
0
0
0
2
t
o
2
"
4
1
0
0
2
t
o
1
(2oz/ft2 .0028"
(3oz/ft2) .0042"
相關PDF資料
PDF描述
P3100SARP SIDAC|350V V(BO) MAX|800MA I(S)|DO-214AA
P3100SBRP SIDAC|350V V(BO) MAX|800MA I(S)|DO-214AA
P3300AA61RP SIDAC|360V V(BO) MAX|800MA I(S)|TO-220VAR
P3500EA 44 PIN, 32 KB ENH FLASH, 1536 RAM, 36 I/O, -40C to +125C, 44-QFN, TUBE
P3500EARP1 SIDAC|400V V(BO) MAX|800MA I(S)|TO-92VAR
相關代理商/技術參數
參數描述
P3100G_LRP 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:Teccor㈢ brand Protection Thyristors
P3100GALRP 功能描述:硅對稱二端開關元件 275V 50A DO15 SIDACtor Bi RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P3100GBLRP 功能描述:硅對稱二端開關元件 275V 80A DO15 SIDACtor Bi RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P3100IGSVB 制造商:Eaton Corporation 功能描述:SWITCH DISCONNECTOR 100A
P3100-N-S 功能描述:LED照明器材 Neutral White 4500K 180 Lumens 75 CRI RoHS:否 制造商: 產品:LED Module Strip LED 數量: 波長/色溫:4500 K 光通量:180 lm 寬度:21.1 mm 長度:304.8 mm 外殼材料:Plastic 系列: 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*