參數資料
型號： P3300AA61
英文描述： solid state crowbar devices
中文描述： 固態撬棍設備
文件頁數： 43/161頁
文件大?。?/td> 986K
代理商： P3300AA61
SIDACtor
Data Book
Customer Premises Equipment (CPE)
Teccor Electronics
(972) 580-7777
3 - 3
R
1-.
Overview
CPE is defined as any telephone terminal equipment which resides at the customers
site and is connected to the public switched telephone network (PSTN). Telephones,
modems, caller ID adjunct boxes, PBX
’
s and answering machines are all considered
CPE.
Protection Requirements
CPE should be protected against over-voltages that can exceed 800V and surge
currents up to 100A. In Figures 3-1 through 3-5, the SIDACtor was chosen because
the associated peak pulse current (I
PP
) is great enough to withstand the lightning
immunity test of FCC Part 68 without the additional use of series line impedance.
Likewise, the fuse in Figures 3-1 through 3-5 was chosen because the amps
2
time (I
2
t)
rating is large enough to withstand the lightning immunity tests of FCC Part 68, but
small enough to pass UL power cross conditions.
Applicable Regulatory Requirements
FCC Part 68
UL 1459
UL 1950
All CPE that is intended for connection to the PSTN must be registered in compliance
with FCC Part 68. Also, because the National Electric Code mandates that
“
equipment
intended for connection to the telephone network be listed for that purpose
”
,
consideration should be given to certifying equipment with an approved safety lab
such as Underwriters Laboratories.
CPE Reference Circuits
Figures 3-1 through 3-5 are examples of interface circuits which meet all applicable
regulatory requirements for CPE. The P3100SB and P3100EB are used in these
circuits because the peak off-state voltage (V
DRM
) is greater than the potential of a
Type B ringer superimposed on a POTS (plain old telephone service) battery.
150V
RMS
√
2 + 56.6Vpk = 268.8Vpk
It should be noted that the circuits shown in Figures 3-1 through 3-5 provide an
operational solution for FCC Part 68, however FCC Part 68 allows CPE designs to
pass non-operationally as well.
For a non-operational solution, the I
PP
rating of the SIDACtor and the I
2
t rating of the
fuse should be coordinated such that both will withstand the Type B surge, but during
the Type A surge, the fuse will open (Table 5-1, Fuse Selection Criteria).
Note: For alternative line interface protection circuits, please refer to Regulatory Requirements
and Regulatory Compliant Solutions.
相關PDF資料
PDF描述
P0080SARP MCU CMOS 44 LD 20MHZ 4K EPRM, -40C to +85C, 44-MQFP, TRAY
P0080SBRP SIDAC|25V V(BO) MAX|800MA I(S)|DO-214AA
P0080SCRP SIDAC|25V V(BO) MAX|800MA I(S)|DO-214AA
P0300EA MCU CMOS 44 LD 4MHZ 8K OTP, 0C to +70C, 44-PLCC, TUBE
P0300EARP1 SIDAC|40V V(BO) MAX|800MA I(S)|TO-92VAR
相關代理商/技術參數
參數描述
P3300AA61L 功能描述:硅對稱二端開關元件 3Chp 300V 50A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P3300AA61RP 功能描述:硅對稱二端開關元件 3Chp 300V 50A RoHS:否 制造商:Bourns 轉折電流 VBO:40 V 最大轉折電流 IBO:800 mA 不重復通態電流: 額定重復關閉狀態電壓 VDRM:25 V 關閉狀態漏泄電流（在 VDRM IDRM 下）: 保持電流（Ih 最大值）:50 mA 開啟狀態電壓:5 V 關閉狀態電容 CO:120 pF 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AA
P3301 制造商:TYAN 功能描述:- Bulk
P-3301 制造商:Eveready 功能描述:
P3-30100 制造商:OTTO Engineering Inc 功能描述:S/A P3-31111 WITH
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*