參數資料
型號： P80C32SBAA,512
廠商： NXP Semiconductors
文件頁數： 5/32頁
文件大?。?/td> 0K
描述： IC 80C51 MCU 8BIT ROMLESS 44PLCC
產品培訓模塊： Migrating from 8/16-Bit MCUs to 32-Bit ARMs
標準包裝： 26
系列： 80C
核心處理器： 8051
芯體尺寸： 8-位
速度： 16MHz
連通性： UART/USART
外圍設備： POR
輸入/輸出數： 32
程序存儲器類型： ROMless
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
振蕩器型： 內部
工作溫度： 0°C ~ 70°C
封裝/外殼： 44-LCC（J 形引線）
包裝： 管件
產品目錄頁面： 705 (CN2011-ZH PDF)
其它名稱： 568-1233-5
935255770512
P80C32SBAA
Philips Semiconductors
Product specification
80C31/80C32
80C51 8-bit microcontroller family
128/256 byte RAM ROMless low voltage (2.7V–5.5V),
low power, high speed (33 MHz)
2000 Aug 07
13
Baud Rate Generator Mode
Bits TCLK and/or RCLK in T2CON (Table 3) allow the serial port
transmit and receive baud rates to be derived from either Timer 1 or
Timer 2. When TCLK= 0, Timer 1 is used as the serial port transmit
baud rate generator. When TCLK= 1, Timer 2 is used as the serial
port transmit baud rate generator. RCLK has the same effect for the
serial port receive baud rate. With these two bits, the serial port can
have different receive and transmit baud rates – one generated by
Timer 1, the other by Timer 2.
Figure 6 shows the Timer 2 in baud rate generation mode. The baud
rate generation mode is like the auto-reload mode, in that a rollover
in TH2 causes the Timer 2 registers to be reloaded with the 16-bit
value in registers RCAP2H and RCAP2L, which are preset by
software.
The baud rates in modes 1 and 3 are determined by Timer 2’s
overflow rate given below:
Modes 1 and 3 Baud Rates
+ Timer 2 Overflow Rate
16
The timer can be configured for either “timer” or “counter” operation.
In many applications, it is configured for “timer” operation (C/T2*=0).
Timer operation is different for Timer 2 when it is being used as a
baud rate generator.
Usually, as a timer it would increment every machine cycle (i.e., 1/12
the oscillator frequency). As a baud rate generator, it increments
every state time (i.e., 1/2 the oscillator frequency). Thus the baud
rate formula is as follows:
Oscillator Frequency
[32
[65536
* (RCAP2H, RCAP2L)]]
Modes 1 and 3 Baud Rates =
Where:
(RCAP2H, RCAP2L)= The content of RCAP2H and
RCAP2L taken as a 16-bit unsigned integer.
The Timer 2 as a baud rate generator mode shown in Figure 6, is
valid only if RCLK and/or TCLK = 1 in T2CON register. Note that a
rollover in TH2 does not set TF2, and will not generate an interrupt.
Thus, the Timer 2 interrupt does not have to be disabled when
Timer 2 is in the baud rate generator mode. Also if the EXEN2
(T2 external enable flag) is set, a 1-to-0 transition in T2EX
(Timer/counter 2 trigger input) will set EXF2 (T2 external flag) but
will not cause a reload from (RCAP2H, RCAP2L) to (TH2,TL2).
Therefore when Timer 2 is in use as a baud rate generator, T2EX
can be used as an additional external interrupt, if needed.
When Timer 2 is in the baud rate generator mode, one should not try
to read or write TH2 and TL2. As a baud rate generator, Timer 2 is
incremented every state time (osc/2) or asynchronously from pin T2;
under these conditions, a read or write of TH2 or TL2 may not be
accurate. The RCAP2 registers may be read, but should not be
written to, because a write might overlap a reload and cause write
and/or reload errors. The timer should be turned off (clear TR2)
before accessing the Timer 2 or RCAP2 registers.
Table 4 shows commonly used baud rates and how they can be
obtained from Timer 2.
Table 4.
Timer 2 Generated Commonly Used
Baud Rates
Ba d Rate
Osc Freq
Timer 2
Baud Rate
Osc Freq
RCAP2H
RCAP2L
375 K
12 MHz
FF
9.6 K
12 MHz
FF
D9
2.8 K
12 MHz
FF
B2
2.4 K
12 MHz
FF
64
1.2 K
12 MHz
FE
C8
300
12 MHz
FB
1E
110
12 MHz
F2
AF
300
6 MHz
FD
8F
110
6 MHz
F9
57
Summary Of Baud Rate Equations
Timer 2 is in baud rate generating mode. If Timer 2 is being clocked
through pin T2(P1.0) the baud rate is:
Baud Rate
+ Timer 2 Overflow Rate
16
If Timer 2 is being clocked internally, the baud rate is:
Baud Rate
+
f
OSC
[32
[65536
* (RCAP2H, RCAP2L)]]
Where fOSC= Oscillator Frequency
To obtain the reload value for RCAP2H and RCAP2L, the above
equation can be rewritten as:
RCAP2H, RCAP2L
+ 65536 *
f
OSC
32
Baud Rate
Timer/Counter 2 Set-up
Except for the baud rate generator mode, the values given for
T2CON do not include the setting of the TR2 bit. Therefore, bit TR2
must be set, separately, to turn the timer on. See Table 5 for set-up
of Timer 2 as a timer. Also see Table 6 for set-up of Timer 2 as a
counter.
相關PDF資料
PDF描述
P80C32UBAA,512 IC 80C51 MCU 8BIT ROMLESS 44PLCC
1-5353583-1 CONN RCPT 4X1 USB RT ANG SMD
5353583-4 CONN RCPT USB 4POS R/A SMD SLD
5353583-1 CONN RCPT USB 4POS R/A SMD SLD
2-1747981-4 CONN RECPT HDMI SMT R/A W/FLNG
相關代理商/技術參數
參數描述
P80C32SBAA-T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
P80C32SBBB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit CMOS (low voltage, low power and high speed) microcontroller families
P80C32SBBB,557 功能描述:8位微控制器 -MCU 128/256B RAM ROMLESS 2.7-5.5V 33MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P80C32SBBB-S 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
P80C32SBPN 制造商:NXP Semiconductors 功能描述:80C 16MHz 制造商:NXP Semiconductors 功能描述:IC 8BIT CPU 80C32 DIP40 制造商:NXP Semiconductors 功能描述:IC, 8BIT CPU, 80C32, DIP40 制造商:NXP Semiconductors 功能描述:IC, 8BIT MCU, 80C51, 16MHZ, DIP-40; Controller Family/Series:(8051) 8052; Core Size:8bit; No. of I/O's:32; Supply Voltage Min:2.7V; Supply Voltage Max:5.5V; Digital IC Case Style:DIP; No. of Pins:40; Program Memory Size:- ;RoHS Compliant: Yes
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*