參數資料
型號： P80C51X2BBD
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 80C51 8-bit microcontroller family 4K/8K/16K/32K ROM/OTP 128B/256B RAM low voltage 2.7 to 5.5 V, low power, high speed 30/33 MHz
中文描述： 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PQFP44
封裝： 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-389-1, LQFP-44
文件頁數： 6/38頁
文件大?。?/td> 350K
代理商： P80C51X2BBD
Philips Semiconductors
Product specification
80C51/87C51/80C31
80C51 8-bit microcontroller family
4K/128 OTP/ROM/ROMless, low voltage (2.7V–5.5V),
low power, high speed (33 MHz)
2000 Jan 20
6
PIN DESCRIPTIONS
PIN NUMBER
DIP
LCC
20
40
39–32
43–36
MNEMONIC
V
SS
V
CC
P0.0–0.7
QFP
16
38
37–30
TYPE
I
I
I/O
NAME AND FUNCTION
Ground:
0V reference.
Power Supply:
This is the power supply voltage for normal, idle, and power-down operation.
Port 0:
Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s written to
them float and can be used as high-impedance inputs. Port 0 is also the multiplexed
low-order address and data bus during accesses to external program and data memory. In
this application, it uses strong internal pull-ups when emitting 1s. Port 0 also outputs the
code bytes during program verification and received code bytes during EPROM
programming. External pull-ups are required during program verification.
Port 1:
Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1 pins that have 1s
written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs,
port 1 pins that are externally pulled low will source current because of the internal pull-ups.
(See DC Electrical Characteristics: I
). Port 1 also receives the low-order address byte
during program memory verification. Alternate functions for Port 1 include:
T2 (P1.0):
Timer/Counter 2 external count input/clockout (see Programmable Clock-Out).
T2EX (P1.1):
Timer/Counter 2 Reload/Capture/Direction control.
Port 2:
Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that have 1s
written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs,
port 2 pins that are externally being pulled low will source current because of the internal
pull-ups. (See DC Electrical Characteristics: I
). Port 2 emits the high-order address byte
during fetches from external program memory and during accesses to external data memory
that use 16-bit addresses (MOVX @DPTR). In this application, it uses strong internal
pull-ups when emitting 1s. During accesses to external data memory that use 8-bit addresses
(MOV @Ri), port 2 emits the contents of the P2 special function register. Some Port 2 pins
receive the high order address bits during EPROM programming and verification.
Port 3:
Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s
written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs,
port 3 pins that are externally being pulled low will source current because of the pull-ups.
(See DC Electrical Characteristics: I
IL
). Port 3 also serves the special features of the 80C51
family, as listed below:
RxD (P3.0):
Serial input port
TxD (P3.1):
Serial output port
INT0 (P3.2):
External interrupt
INT1 (P3.3):
External interrupt
T0 (P3.4):
Timer 0 external input
T1 (P3.5):
Timer 1 external input
WR (P3.6):
External data memory write strobe
RD (P3.7):
External data memory read strobe
Reset:
A high on this pin for two machine cycles while the oscillator is running, resets the
device. An internal diffused resistor to V
SS
permits a power-on reset using only an external
capacitor to V
CC
.
Address Latch Enable/Program Pulse:
Output pulse for latching the low byte of the
address during an access to external memory. In normal operation, ALE is emitted at a
constant rate of 1/6 the oscillator frequency, and can be used for external timing or clocking.
Note that one ALE pulse is skipped during each access to external data memory. This pin is
also the program pulse input (PROG) during EPROM programming. ALE can be disabled by
setting SFR auxiliary.0. With this bit set, ALE will be active only during a MOVX instruction.
Program Store Enable:
The read strobe to external program memory. When the 8XC51/31
is executing code from the external program memory, PSEN is activated twice each
machine cycle, except that two PSEN activations are skipped during each access to
external data memory. PSEN is not activated during fetches from internal program memory.
External Access Enable/Programming Supply Voltage:
EA must be externally held low
to enable the device to fetch code from external program memory locations 0000H and
0FFFH. If EA is held high, the device executes from internal program memory unless the
program counter contains an address greater than 0FFFH. This pin also receives the
12.75V programming supply voltage (V
) during EPROM programming. If security bit 1 is
programmed, EA will be internally latched on Reset.
Crystal 1:
Input to the inverting oscillator amplifier and input to the internal clock generator
circuits.
Crystal 2:
Output from the inverting oscillator amplifier.
22
44
P1.0–P1.7
1–8
2–9
40–44,
1–3
I/O
1
2
2
3
40
41
I/O
I
I/O
P2.0–P2.7
21–28
24–31
18–25
P3.0–P3.7
10–17
11,
13–19
5,
7–13
I/O
10
11
12
13
14
15
16
17
9
11
13
14
15
16
17
18
19
10
5
7
8
9
10
11
12
13
4
I
O
I
I
I
I
O
O
I
RST
ALE/PROG
30
33
27
O
PSEN
29
32
26
O
EA/V
PP
31
35
29
I
XTAL1
19
21
15
I
XTAL2
NOTE:
To avoid “l(fā)atch-up” effect at power-on, the voltage on any pin at any time must not be higher than V
CC
+ 0.5V or V
SS
– 0.5V, respectively.
18
20
14
O
相關PDF資料
PDF描述
P80C51UBPN 80C51 8-bit microcontroller family 4K/128 OTP/ROM/ROMless low voltage 2.7V.5.5V, low power, high speed 33 MHz
P80C31UBPN 80C51 8-bit microcontroller family 4K/128 OTP/ROM/ROMless low voltage 2.7V.5.5V, low power, high speed 33 MHz
P80C51SFBB 80C51 8-bit microcontroller family 4K/128 OTP/ROM/ROMless low voltage 2.7V.5.5V, low power, high speed 33 MHz
P80C31SFBB 80C51 8-bit microcontroller family 4K/128 OTP/ROM/ROMless low voltage 2.7V.5.5V, low power, high speed 33 MHz
P80C31SFPN 80C51 8-bit microcontroller family 4K/128 OTP/ROM/ROMless low voltage 2.7V.5.5V, low power, high speed 33 MHz
相關代理商/技術參數
參數描述
P80C51X2BN 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 8-bit microcontroller family 4K/8K/16K/32K ROM/OTP 128B/256B RAM low voltage 2.7 to 5.5 V, low power, high speed 30/33 MHz
P80C51X2FA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 8-bit microcontroller family 4K/8K/16K/32K ROM/OTP 128B/256B RAM low voltage 2.7 to 5.5 V, low power, high speed 30/33 MHz
P80C51X2FBD 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 8-bit microcontroller family 4K/8K/16K/32K ROM/OTP 128B/256B RAM low voltage 2.7 to 5.5 V, low power, high speed 30/33 MHz
P80C52 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
P80C521 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:CMOS SINGLE CHIP MICROCONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*