參數資料
型號: P80C592
廠商: NXP Semiconductors N.V.
英文描述: 8-bit microcontroller with on-chip CAN
中文描述: 8位微控制器芯片的CAN
文件頁數: 18/108頁
文件大?。?/td> 650K
代理商: P80C592
1996 Jun 27
18
Philips Semiconductors
Product specification
8-bit microcontroller with on-chip CAN
P8xC592
Fig.9 Functional diagram of Pulse Width Modulated outputs.
handbook, full pagewidth
MGA154
I
N
T
E
R
N
A
L
B
U
S
fclk
PWMP
PWM1
PRESCALER
8-BIT COUNTER
1/2
PWM0
8-BIT COMPARATOR
8-BIT COMPARATOR
OUTPUT
BUFFER
PWM1
OUTPUT
BUFFER
PWM0
10 ANALOG-TO-DIGITAL CONVERTER (ADC)
The analog input circuitry consists of an 8-input analog
multiplexer and an ADC with 10-bit resolution. The analog
reference voltage and analog power supplies are
connected via separate input pins. The conversion takes
50 machine cycles i.e. 37.5
μ
s at 16 MHz oscillator
frequency. The input voltage swing is from 0 V to AV
DD
.
The ADC is controlled using the ADCON control register.
Register bits ADCON.0 to ADCON.2 select the input
channels of the analog multiplexer (see Fig.10).
The completion of the 10-bit analog-to-digital conversion is
flagged by ADCI in the ADCON register and the result is
stored in the SFR ADCH (upper 8-bits) and the 2 lower bits
(ADC.1 and ADC.0) in register ADCON.
An analog-to-digital conversion in progress is unaffected
by an external or software ADC start. The result of a
completed conversion remains unchanged provided
ADCI = HIGH. While ADCI or ADCS are HIGH, a new ADC
START will be blocked and consequently lost. An
analog-to-digital conversion already in progress is aborted
when the Idle or Power-down mode is entered.
The result of a completed conversion (ADCI = HIGH)
remains unaffected during the Idle mode.
The LOW-to-HIGH transition of STADC is recognized at
the end of a machine cycle and the conversion
commences at the beginning of the next cycle. When a
conversion is initiated by software, the conversion starts at
the beginning of the machine cycle following the
instruction that sets ADCS.
The next two machine cycles are used to initiate the
converter. At the end of this first cycle, the ADCS status
flag is set to HIGH while the conversion is in progress.
Sampling of the analog input commences at the end of the
second cycle.
During the next eight machine cycles, the voltage at the
previously selected pin of Port 5 is sampled and this input
voltage should be stable in order to obtain a useful sample.
In any case, the input voltage slew rate must be less than
10 V/ms (5 V conversion range) in order to prevent an
undefined result. The conversion takes four machine
cycles per bit.
相關PDF資料
PDF描述
P83C592 8-bit microcontroller with on-chip CAN
P87C592EFA 8-bit microcontroller with on-chip CAN
P8xC592 8-bit microcontroller with on-chip CAN
P83C652EBAA CMOS single-chip 8-bit microcontrollers
P83C652EHBB CMOS single-chip 8-bit microcontrollers
相關代理商/技術參數
參數描述
P80C592FFA 制造商:NXP Semiconductors 功能描述:
P80C592FFA/00,512 功能描述:8位微控制器 -MCU 80C51 W/CAN 16MHZ ROMLESS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P80C592FFA/00,512 制造商:NXP Semiconductors 功能描述:8BIT MCU+CAN, SMD, 80C592, PLCC68
P80C592FFA/00,518 功能描述:8位微控制器 -MCU SINGLE-CHIP 8-BIT MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P80C592FFA/00 制造商:NXP Semiconductors 功能描述:8BIT MCU+CAN SMD 80C592 PLCC68