參數資料
型號： P80CL410
廠商： NXP Semiconductors N.V.
英文描述： Low voltage 8-bit microcontrollers with I2C-bus
中文描述： 低電壓的8位微控制器帶有I2C總線
文件頁數： 24/60頁
文件大?。?/td> 266K
代理商： P80CL410
1997 Apr 10
24
Philips Semiconductors
Product specification
Low voltage 8-bit microcontrollers with
I
2
C-bus
P80CL410; P83CL410
14 INTERRUPT SYSTEM
External events and the real-time-driven on-chip
peripherals require service by the CPU at unpredictable
times. To tie the asynchronous activities of these functions
to normal program execution a multiple-source,
two-priority-level, nested interrupt system is provided.
The system is shown in Fig.12. The P8xCL410
acknowledges interrupt requests from thirteen sources as
follows:
INT0 and INT1
Timer 0 and Timer 1
I
2
C-bus
INT2 to INT9.
Each interrupt vectors to a separate location in Program
Memory for its service routine. Each source can be
individually enabled or disabled by corresponding bits in
the Interrupt Enable Registers (IEN0 and IEN1).
The priority level is selected via the Interrupt Priority
Registers (IP0 and IP1). All enabled sources can be
globally disabled or enabled. Figure 12 shows the interrupt
system.
14.1
External interrupts INT2 to INT9
Port 1 lines serve an alternative purpose as eight
additional interrupts INT2 to INT9. When enabled, each of
these lines may wake-up the device from the Power-down
mode. Using the Interrupt Polarity Register (IX1), each pin
may be initialized to be either active HIGH or active LOW.
IRQ1 is the Interrupt Request Flag Register. If the interrupt
is enabled, each flag will be set on an interrupt request but
must be cleared by software, i.e. via the interrupt software
or when the interrupt is disabled.
Port 1 interrupts are level sensitive. A Port 1 interrupt will
be recognized when a level (HIGH or LOW depending on
the Interrupt Polarity Register) on P1.n is held active for at
least one machine cycle. The interrupt request is not
serviced until the next machine cycle. Figure 13 shows the
external interrupt configuration.
14.2
Interrupt priority
Each interrupt source can be set to either a high priority or
to a low priority. If a low priority interrupt is received
simultaneously with a high priority interrupt, the high
priority interrupt will be dealt with first.
If interrupts of the same priority are requested
simultaneously, the processor will branch to the interrupt
polled first, according to the sequence shown in Table 19
and in Fig.12. The ‘vector address’ is the ROM location
where the appropriate interrupt service routine starts.
Table 19
Interrupt vector polling sequence
A low priority interrupt routine can only be interrupted by a
high priority interrupt. A high priority interrupt routine
cannot be interrupted.
SYMBOL
VECTOR
ADDRESS (HEX)
SOURCE
X0 (first)
S1
X5
T0
X6
X1
X2
X7
T1
X3
X8
X4
X9 (last)
0003
002B
0053
000B
005B
0013
003B
0063
001B
0043
006B
004B
xt0073
External 0
I
2
C port
External 5
Timer 0
External 6
External 1
External 2
External 7
Timer 1
External 3
External 8
External 4
External 9
相關PDF資料
PDF描述
P83CL410 Low voltage 8-bit microcontrollers with I2C-bus
P80CL580HFB 8-BIT MICROCONTROLLER
P83CL168H 8-BIT MICROCONTROLLER
P83CL411HFT 8-BIT MICROCONTROLLER
P83CL580HFB 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
P80CL410HFD 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
P80CL410HFD-T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
P80CL410HFN 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low voltage/low power single-chip 8-bit microcontroller with I2C
P80CL410HFP 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low voltage 8-bit microcontrollers with I2C-bus
P80CL410HFT 制造商:NXP Semiconductors 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*