- 您現在的位置：買賣IC網 > PDF目錄369944 > P87C511 (Intel Corp.) CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | P87C511 |
| 廠商： | Intel Corp. |
| 英文描述： | CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER |
| 中文描述： | CHMOS單片8位微控制器 |
| 文件頁數： | 4/21頁 |
| 文件大?。?/td> | 284K |
| 代理商： | P87C511 |
87C51/80C51BH/80C31BH
PIN DESCRIPTION
V
CC
:
Supply voltage during normal, Idle and Power
Down operations.
V
SS
:
Circuit ground.
Port 0:
Port 0 is an 8-bit open drain bidirectional I/O
port. As an output port each pin can sink several LS
TTL inputs. Port 0 pins that have 1’s written to them
float, and in that state can be used as high-imped-
ance inputs.
Port 0 is also the multiplexed low-order address and
data bus during accesses to external memory. In this
application it uses strong internal pullups when emit-
ting 1’s.
Port 0 also receives the code bytes during EPROM
programming, and outputs the code bytes during
program verification. External pullups are required
during program verification.
Port 1:
Port 1 is an 8-bit bidirectional I/O port with
internal pullups. The Port 1 output buffers can drive
LS TTL inputs. Port 1 pins that have 1’s written to
them are pulled high by the internal pullups, and in
that state can be used as inputs. As inputs, Port 1
pins that are externally pulled low will source current
(I
IL
, on the data sheet) because of the internal pull-
ups.
Port 1 also receives the low-order address bytes
during EPROM programming and program verifica-
tion.
Port 2:
Port 2 is an 8-bit bidirectional I/O port with
internal pullups. Port 2 pins that have 1’s written to
them are pulled high by the internal pullups, and in
that state can be used as inputs. As inputs, Port 2
pins that are externally pulled low will source current
(I
IL
, on the data sheet) because of the internal pull-
ups.
Port 2 emits the high-order address byte during
fetches from external Program memory and during
accesses to external Data Memory that use 16-bit
address (MOVX
@
DPTR). In this application it uses
strong internal pullups when emitting 1’s.
During accesses to external Data Memory that use
8-bit addresses (MOVX
@
Ri), Port 2 emits the con-
tents of the P2 Special Function Register.
Port 2 also receives some control signals and the
high-order address bits during EPROM programming
and program verification.
Port 3:
Port 3 is an 8-bit bidirectional I/O port with
internal pullups. The Port 3 output buffers can drive
LS TTL inputs. Port 3 pins that have 1’s written to
them are pulled high by the internal pullups, and in
that state can be used as inputs. As inputs, Port 3
pins that are externally pulled low will source current
(I
IL
, on the data sheet) because of the pullups.
Port 3 also serves the functions of various special
features of the MCS-51 Family, as listed below:
Pin
Name
Alternate Function
P3.0
P3.1
P3.2
P3.3
P3.4
P3.5
P3.6
P3.7
RXD
TXD
INT0
INT1
T0
T1
WR
RD
Serial input line
Serial output line
External Interrupt 0
External Interrupt 1
Timer 0 external input
Timer 1 external input
External Data Memory Write strobe
External Data Memory Read strobe
Port 3 also receives some control signals for
EPROM programming and program verification.
RST:
Reset input. A high on this pin for two machine
cycles while the oscillator is running resets the de-
vice. The port pins will be driven to their reset condi-
tion when a minimum V
IH1
voltage is applied wheth-
er the oscillator is running or not. An internal pull-
down resistor permits a power-on reset with only a
capacitor connected to V
CC
.
ALE/PROG:
Address Latch Enable output signal for
latching the low byte of the address during accesses
to external memory. This pin is also the program
pulse input (PROG) during EPROM programming for
the 87C51.
If desired, ALE operation can be disabled by setting
bit 0 of SFR location 8EH. With this bit set, the pin is
weakly pulled high. However, the ALE disable fea-
ture will be suspended during a MOVX or MOVC in-
struction, idle mode, power down mode and ICE
mode. The ALE disable feature will be terminated by
reset. When the ALE disable feature is suspended or
terminated, the ALE pin will no longer be pulled up
weakly. Setting the ALE-disable bit has no effect if
the microcontroller is in external execution mode.
4
相關PDF資料 |
PDF描述 |
|---|---|
| P87LPC759 | Low power, low price, low pin count (14 pin) microcontroller with 1 kbyte OTP |
| P87LPC759BN | Low power, low price, low pin count (14 pin) microcontroller with 1 kbyte OTP |
| P89C738 | 8-bit Flash microcontrollers |
| P89C739ABA | 8-bit Flash microcontrollers |
| P89C739ABB | 8-bit Flash microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P87C51-1 | 制造商:. 功能描述: |
| P87C511 S F76 | 制造商:Intel 功能描述:MCU 8-bit MCS51 80C51 CISC 4KB EPROM 5V 40-Pin PDIP |
| P87C511SF76 | 功能描述:IC MCU 8BIT 5V 16MHZ OTP 40DIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:87C 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND |
| P87C51-24 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| P87C5124 S F76 | 制造商:Intel 功能描述:MCU 8-bit MCS51 80C51 CISC 4KB EPROM 5V 40-Pin PDIP |
發布緊急采購，3分鐘左右您將得到回復。