參數資料
型號： P87LPC768FD,512
廠商： NXP Semiconductors
文件頁數： 4/65頁
文件大?。?/td> 0K
描述： IC 80C51 MCU 4K OTP 20-SOIC
產品培訓模塊： Migrating from 8/16-Bit MCUs to 32-Bit ARMs
標準包裝： 38
系列： LPC700
核心處理器： 8051
芯體尺寸： 8-位
速度： 20MHz
連通性： I²C，UART/USART
外圍設備： 欠壓檢測/復位，LED，POR，PWM，WDT
輸入/輸出數： 18
程序存儲器容量： 4KB（4K x 8）
程序存儲器類型： OTP
RAM 容量： 128 x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 6 V
數據轉換器： A/D 4x8b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 20-SOIC（0.295"，7.50mm 寬）
包裝： 管件
產品目錄頁面： 706 (CN2011-ZH PDF)
其它名稱： 568-3219-5
935267487512
P87LPC768FD
Philips Semiconductors
Preliminary data
P87LPC768
Low power, low price, low pin count (20 pin) microcontroller
with 4 kB OTP 8-bit A/D, Pulse Width Modulator
2002 Mar 12
10
ADCON
Address: C0h
Bit addressable
Reset Value: 00h
BIT
SYMBOL
FUNCTION
ADCON.7
ENADC
When ENADC = 1, the A/D is enabled and conversions may take place. Must be set 10
microseconds before a conversion is started. ENADC cannot be cleared while ADCS or ADCI
are 1.
ADCON.6
-
Reserved for future use. Should not be set to 1 by user programs.
ADCON.5
-
Reserved for future use. Should not be set to 1 by user programs.
ADCON.4
ADCI
A/D conversion complete/interrupt flag. This flag is set when an A/D conversion is completed.
This bit will cause a hardware interrupt if enabled and of sufficient priority. Must be cleared by
software.
ADCON.3
ADCS
A/D start. Setting this bit by software starts the conversion of the selected A/D input. ADCS
remains set while the A/D conversion is in progress and is cleared automatically upon
completion. While ADCS or ADCI are one, new start commands are ignored.
ADCI, ADCS
A/D Status
0 0
A/D not busy, a conversion can be started.
0 1
A/D busy, the start of a new conversion is blocked.
1 0
An A/D conversion is complete. ADCI must be cleared prior to starting a new conversion.
1 1
An A/D conversion is complete. ADCI must be cleared prior to starting a new conversion. This
state exists for one machine cycle as an A/D conversion is completed.
ADCON.2
RCCLK
When RCCLK = 0, the CPU clock is used as the A/D clock. When RCCLK = 1, the internal RC
oscillator is used as the A/D clock. This bit is writable while ADCS and ADCI are 0.
ADCON.1, 0
AADR1,0
Along with AADR0, selects the A/D channel to be converted. These bits can only be written
while ADCS and ADCI are 0.
AADR1, AADR0
A/D Input Selected
0 0
AD0 (P0.3).
0 1
AD1 (P0.4).
1 0
AD2 (P0.5).
1 1
AD3 (P0.6).
7
6
54
32
10
ENADC
-
ADCI
ADCS
RCCLK
AADR1
AADR0
SU01354
Figure 2. A/D Control Register (ADCON)
A/D Timing
The A/D may be clocked in one of two ways. The default is to use
the CPU clock as the A/D clock source. When used in this manner,
the A/D completes a conversion in 31 machine cycles. The A/D may
be operated up to the maximum CPU clock rate of 20 MHz, giving a
conversion time of 9.3
s. The formula for calculating A/D
conversion time when the CPU clock runs the A/D is: 186
s / CPU
clock rate (in MHZ). To obtain accurate A/D conversion results, the
CPU clock must be at least 1 MHz.
The A/D may also be clocked by the on-chip RC oscillator, even if
the RC oscillator is not used as the CPU clock. This is accomplished
by setting the RCCLK bit in ADCON. This arrangement has several
advantages. First, the A/D conversion time is faster at lower CPU
clock rates. Also, the CPU may be run at speeds below 1 MHz
without affecting A/D accuracy. Finally, the Power Down mode may
be used to completely shut down the CPU and its oscillator, along
with other peripheral functions, in order to obtain the best possible
A/D accuracy. This should not be used if the MCU uses an external
clock source greater than 4 MHz.
When the A/D is operated from the RCCLK while the CPU is running
from another clock source, 3 or 4 machine cycles are used to
synchronize A/D operation. The time can range from a minimum of 3
machine cycles (at the CPU clock rate) + 108 RC clocks to a
maximum of 4 machine cycles (at the CPU clock rate) + 112 RC
clocks.
Example A/D conversion times at various CPU clock rates are
shown in Table 1. In Table 1, maximum times for RCCLK = 1 use an
RC clock frequency of 4.5 MHz (6 MHz - 25%). Minimum times for
RCCLK = 1 use an RC clock frequency of 7.5 MHz (6 MHz + 25%).
Nominal time assume an ideal RC clock frequency of 6 MHz and an
average of 3.5 machine cycles at the CPU clock rate.
相關PDF資料
PDF描述
HI1-5042-2 IC SWITCH SPDT 16CDIP
NB4L858MFAR2G IC CROSSPOINT SWITCH DUAL 32LQFP
HI1-0509-2 IC MULTIPLEXER DUAL 4X1 16CDIP
EFM32TG210F8 MCU 32BIT 8KB FLASH 32-QFN
HI9P5051-9Z IC SWITCH DUAL SPDT 16SOIC
相關代理商/技術參數
參數描述
P87LPC768FN 制造商:NXP Semiconductors 功能描述:MCU 8-Bit 87LP 80C51 CISC 4KB EPROM 5V 20-Pin PDIP
P87LPC768FN,112 功能描述:8位微控制器 -MCU 80C51 4K/128 OTP ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P87LPC769 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low power, low price, low pin count 20 pin microcontroller with 4 kB OTP 8-bit A/D, and DAC
P87LPC769HD 功能描述:8位微控制器 -MCU 80C51 4K/128 OTP ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P87LPC769HD,512 功能描述:8位微控制器 -MCU 80C51 4K/128 OTP ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*