- 您現在的位置：買賣IC網 > PDF目錄11173 > P89LPC933HDH,512 (NXP Semiconductors)IC 80C51 MCU 4KB FLASH 28TSSOP PDF資料下載
參數資料
| 型號： | P89LPC933HDH,512 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 27/77頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 80C51 MCU 4KB FLASH 28TSSOP |
| 標準包裝： | 51 |
| 系列： | LPC900 |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 18MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，LED，POR，PWM，WDT |
| 輸入/輸出數： | 26 |
| 程序存儲器容量： | 4KB（4K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 256 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.4 V ~ 3.6 V |
| 數據轉換器： | A/D 4x8b; D/A 1x8b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 包裝： | 管件 |
| 其它名稱： | 568-8746-5 P89LPC933HDH,512-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁
P89LPC933_934_935_936
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 12 January 2011
33 of 77
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
8.15.3 Total Power-down mode
This is the same as Power-down mode except that the brownout detection circuitry and
the voltage comparators are also disabled to conserve additional power. The internal RC
oscillator is disabled unless both the RC oscillator has been selected as the system clock
and the RTC is enabled. If the internal RC oscillator is used to clock the RTC during
power-down, there will be high power consumption. Please use an external low frequency
clock to achieve low power with the RTC running during power-down.
8.16 Reset
The P1.5/RST pin can function as either a LOW-active reset input or as a digital input,
P1.5. The Reset Pin Enable (RPE) bit in UCFG1, when set to logic 1, enables the external
reset input function on P1.5. When cleared, P1.5 may be used as an input pin.
Remark: During a power-up sequence, the RPE selection is overridden and this pin will
always functions as a reset input. An external circuit connected to this pin should not
hold this pin LOW during a power-on sequence as this will keep the device in reset.
After power-up this input will function either as an external reset input or as a digital input
as defined by the RPE bit. Only a power-up reset will temporarily override the selection
defined by RPE bit. Other sources of reset will not override the RPE bit. When this pin
functions as a reset input, an internal pull-up resistance is connected (see Table 11 “Static
Reset can be triggered from the following sources:
External reset pin (during power-up or if user configured via UCFG1).
Power-on detect.
Brownout detect.
Watchdog timer.
Software reset.
UART break character detect reset.
For every reset source, there is a flag in the reset register, RSTSRC. The user can read
this register to determine the most recent reset source. These flag bits can be cleared in
software by writing a logic 0 to the corresponding bit. More than one flag bit may be set:
During a power-on reset, both POF and BOF are set but the other flag bits are
cleared.
For any other reset, previously set flag bits that have not been cleared will remain set.
8.16.1 Reset vector
Following reset, the P89LPC933/934/935/936 will fetch instructions from either address
0000H or the boot address. The boot address is formed by using the boot vector as the
high byte of the address and the low byte of the address = 00H.
The boot address will be used if a UART break reset occurs, or the non-volatile boot
status bit (BOOTSTAT.0) = 1, or the device is forced into ISP mode during power-on (see
P89LPC933/934/935/936 User manual). Otherwise, instructions will be fetched from
address 0000H.
相關PDF資料 |
PDF描述 |
|---|---|
| P89LPC9321FDH,512 | IC 80C51 MCU 8KB FLASH 28TSSOP |
| P89LPC9321FDH,518 | IC 80C51 MCU FLASH 8K 28-TSSOP |
| VI-BN3-IX-F4 | CONVERTER MOD DC/DC 24V 75W |
| VI-BN3-IX-F3 | CONVERTER MOD DC/DC 24V 75W |
| VI-BN3-IX-F1 | CONVERTER MOD DC/DC 24V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC934 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 4 kB/8 kB/16 kB 3 V byte-erasable Flash with 8-bit ADCs |
| P89LPC9341FDH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core, 4 kB/8 kB/16 kB 3 V byte-erasable flash with 8-bit ADCs |
| P89LPC9341FDH,512 | 功能描述:8位微控制器 -MCU IC 80C51 MCU FLASH 8K RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC934FDH | 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 8K FLASH TSSOP28 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 8K FLASH, TSSOP28, Controller Family/Series:(8051) 8052, Core Siz |
| P89LPC934FDH,529 | 功能描述:8位微控制器 -MCU 80C51 8K FL 256B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。