- 您現在的位置：買賣IC網 > PDF目錄367729 > P8xC592 (NXP Semiconductors N.V.) 8-bit microcontroller with on-chip CAN PDF資料下載
參數資料
| 型號： | P8xC592 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 8-bit microcontroller with on-chip CAN |
| 中文描述： | 8位微控制器芯片的CAN |
| 文件頁數： | 70/108頁 |
| 文件大小： | 650K |
| 代理商： | P8XC592 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁當前第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
1996 Jun 27
70
Philips Semiconductors
Product specification
8-bit microcontroller with on-chip CAN
P8xC592
16 OSCILLATOR CIRCUITRY
The oscillator circuitry of the P8xC592 is a single-stage
inverting amplifier in a Pierce oscillator configuration. The
circuitry between XTAL1 and XTAL2 is basically an
inverter biased to the transfer point. Either a crystal or
ceramic resonator can be used as the feedback element to
complete the oscillator circuitry. Both are operated in
parallel resonance. XTAL1 (pin 34) is the high gain
amplifier input, and XTAL2 (pin 33) is the output
(see Fig.23). If XTAL1 is driven from an external source,
XTAL2 must be left open (see Fig.24).
Fig.23 P8xC592 oscillator circuit.
handbook, halfpage
C1
XTAL1
XTAL2
20 pF
C2
MLA888
20 pF
34
33
Fig.24 Driving P8xC592 from an external source.
handbook, halfpage
XTAL1
XTAL2
MLA889
external clock
(not TTL compatible)
not connected
34
33
17 RESET CIRCUITRY
The reset pin RST is connected to a Schmitt trigger for
noise rejection (see Fig.25). A reset is accomplished by
holding the RST pin HIGH for at least two machine cycles
(24 oscillator periods). The CPU responds by executing an
internal reset. During reset ALE and PSEN output a HIGH
level. In order to perform a correct reset, this level must not
be affected by external elements.
Also with the P8xC592, the RST line can be pulled HIGH
internally by a pull-up transistor activated by the Watchdog
timer T3. The length of the output pulse from T3 is
3 machine cycles. A pulse of such short duration is
necessary in order to recover from a processor or system
fault as fast as possible.
During Power-down a reset could be generated internally
via the CAN Wake-Up interrupt. Then the RST pin is pulled
HIGH for 6144 machine cycles. In this case the
CAN-controller is not reset.
If the Watchdog timer or the CAN Wake-Up interrupt is
used to reset external devices, the usual capacitor
arrangement for Power-on-reset (see Fig.26) should not
be used.
However, the internal reset is forced, independent of the
external level on the RST pin.
The MAIN RAM and AUXILIARY RAM are not affected.
When V
DD
is turned on, the RAM content is indeterminate.
A reset leaves the internal registers as shown in Table 83.
handbook, halfpage
MGA170 - 1
overflow timer T3
RST
on-chip
RST
R
wake-up reset
CAN
CPU
Fig.25 On-chip reset configuration.
相關PDF資料 |
PDF描述 |
|---|---|
| P83C652EBAA | CMOS single-chip 8-bit microcontrollers |
| P83C652EHBB | CMOS single-chip 8-bit microcontrollers |
| P80C652EHBB | CMOS single-chip 8-bit microcontroller |
| P83C652FFP | CMOS single-chip 8-bit microcontrollers |
| P80C652FFP | CMOS single-chip 8-bit microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P8XCE598 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with on-chip CAN |
| P8XCL580HFH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low voltage 8-bit microcontrollers with UART, I2C-bus and ADC |
| P8XCL580HFT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low voltage 8-bit microcontrollers with UART, I2C-bus and ADC |
| P8Z77 DELUXE | 制造商:Asus 功能描述:P8Z77-V Deluxe ATX Motherboard |
| P8Z77 M PRO | 制造商:Asus 功能描述:P8Z77-M Pro MicroATX Motherboard |
發布緊急采購，3分鐘左右您將得到回復。