- 您現在的位置：買賣IC網 > PDF目錄378040 > PBL38570 (ERICSSON) Universal Speech Circuit PDF資料下載
參數資料
| 型號： | PBL38570 |
| 廠商： | ERICSSON |
| 英文描述： | Universal Speech Circuit |
| 中文描述： | 通用語音電路 |
| 文件頁數： | 5/12頁 |
| 文件大?。?/td> | 238K |
| 代理商： | PBL38570 |
PBL 385 70
5
Functional description
Design procedure
; ref. to fig.4.
The design is made easier through that all settable parameters are returned to ground (-line) this feature differs it from bridge
type solutions. To set the parameters in the following order will result in that the interaction between the same is minimized.
1.
Set the circuit impedance to the line, either 600
or complex. (R3 and C1). C1 should be big enough to give low
impedance compared with R3 in the telephone speech frequency band. Too large C1 will make the start-up slow.
See fig. 6.
Set the DC-characteristic that is required in the PTT specification or in case of a system telephone in the PBX
specification (R6). There are also internal circuit dependent requirements like supply voltages etc.
Set the attac point where the line length regulation is supposed to cut in (R1 and R2). Note that in some countries
the line length regulation is not allowed. In most cases the endresult is better and more readily achieved by using
the line length regulation (line loss compensation) than without. See fig. 12.
Set the transmitter gain and frequency response.
Set the receiver gain and frequency response. See text how to limit the max. swing to the earphone.
Adjust the side tone balancing network.
Set the RFI suppression components in case necessary. In two piece telephones the often ”helically”
wound cord acts as an aerial. The microphone input with its high gain is especially sensitive.
Circuit protection. Apart from any other protection devices used in the design a good practice is to connect a 15V 1W
zener diode across the circuit , from pin 1 to -Line.
2.
3.
4.
5.
6.
7.
8.
Impedance to the line
The AC- impedance to the line is set by
R3, C1 and C2. Fig.4. The circuits relatively
high parallel impedance will not influence
it to any noticeable extent. At low
frequencies the influence of C1 can not be
neglected. Series resistance of C1 that is
dependent on temperature and quality will
cause some of the line signal to enter pin
4. This generates a closed loop in the
transmitter amplifier that will create an
active impedance thus lowering the
impedance to the line. The impedance at
high frequencies is set by C2 that also
acts as a RFI suppressor.
In many specifications the impedance
towards the line is specified as a complex
network. See fig. 6. In case a). the error
signal entering pin 4 is set by the ratio
≈
Rs/
R19 (909
), where in case b). the ratio at
high frequencies will be Rs/220
because
the 820
resistor is bypassed by a
capacitor. To help up this situation the
complex network capacitor is connected
directly to ground (-line), case c). making
the ratio Rs/220
+820
and thus less-
ening the error signal. Conclusion: Connect
like in case c) when complex impedance
is specified.
1
2
+Line
R3
R6
PBL 385 70
+
3
C1
C2
-Line
Rs
≈
1
How to connect a
complex network.
Example:
a)
b)
c)
4
Figure 6. AC-impedence
相關PDF資料 |
PDF描述 |
|---|---|
| PBL385701N | Universal Speech Circuit |
| PBL385701SO | Universal Speech Circuit |
| PBL385711SOS | High current Speech and Line interface Circuit |
| PBL38571 | High current Speech and Line interface Circuit |
| PBL385711NS | High current Speech and Line interface Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PBL385701N | 制造商:ERICSSON 制造商全稱:Ericsson 功能描述:Universal Speech Circuit |
| PBL385701SO | 制造商:ERICSSON 制造商全稱:Ericsson 功能描述:Universal Speech Circuit |
| PBL385701SOT | 制造商:ERICSSON 制造商全稱:Ericsson 功能描述:Universal Speech Circuit |
| PBL38571 | 制造商:ERICSSON 制造商全稱:Ericsson 功能描述:High current Speech and Line interface Circuit |
| PBL38571/1NS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecomm/Datacomm |
發布緊急采購，3分鐘左右您將得到回復。