參數資料
型號： PC7457VGU933L
廠商： Atmel Corp.
英文描述： PowerPC 7457 RISC Microprocessor
中文描述： 7457的PowerPC RISC微處理器
文件頁數： 48/66頁
文件大?。?/td> 522K
代理商： PC7457VGU933L
48
PC7457/47 [Preliminary]
5345B–HIREL–02/04
Notes:
1. OV
DD
supplies power to the processor bus, JTAG, and all control signals except the L3 cache controls (L3CTL[0:1]); GV
DD
supplies power to the L3 cache interface (L3ADDR[0:17], L3DATA[0:63], L3DP[0:7], L3_ECHO_CLK[0:3], and L3_CLK[0:1])
and the L3 control signals L3_CNTL[0:1]; and V
DD
supplies power to the processor core and the PLL (after filtering to
become AV
DD
). For actual recommended value of V
IN
or supply voltages, see Table 3 on page 12.
2. Unused address pins must be pulled down to GND.
3. These pins require weak pull-up resistors (for example, 4.7 k
) to maintain the control signals in the negated state after they
have been actively negated and released by the PC7457 and other bus masters.
4. This signal selects between MPX bus mode (asserted) and 60x bus mode (negated) and will be sampled at HRESET going
high.
5. This signal must be negated during reset, by pull up to OV
DD
or negation by HRESET (inverse of HRESET), to ensure
proper operation.
6. To program the processor interface I/O voltage, connect BVSEL to either GND (selects 1.8V) or to HRESET (selects 2.5V).
To program the L3 interface, connect L3VSEL to either GND (selects 1.8V) or to HRESET (selects 2.5V). If used, pull-down
resistors should be less than 250
.
7. Internal pull up on die.
8. Ignored in 60x bus mode.
9. These signals must be pulled down to GND if unused or if the PC7457 is in 60x bus mode.
10. These input signals for factory use only and must be pulled down to GND for normal machine operation.
11. Power must be supplied to GV
DD
, even when the L3 interface is disabled or unused.
12. It is recommended that this test signal be tied to HRESET; however, other configurations will not adversely affect
performance.
13. These input signals are for factory use only and must be pulled up to OV
DD
for normal machine operation.
14. These signals are for factory use only and must be left unconnected for normal machine operation.
15. This pin can externally cause a performance monitor event. Counting of the event is enabled via software.
16. This signal must be asserted during reset, by pull down to GND or assertion by HRESET, to ensure proper operation.
17. These pins are internally connected to V
DD
. They are intended to allow an external device to detect the core voltage level
present at the processor core. If unused, they must be connected directly to V
DD
or left unconnected.
Signal Name
Pin Number
Active
I/O
I/F Select
(1)
TEST[0:5]
(13)
B10, H6, H10, D8, F9, F8
–
Input
BVSEL
TEST[6]
(10)
A9
–
Input
BVSEL
TMS
(7)
K4
High
Input
BVSEL
TRST
(7)(16)
C1
Low
Input
BVSEL
TS
(3)
P5
Low
I/O
BVSEL
TSIZ[0:2]
L1,H3,D1
High
Output
BVSEL
TT[0:4]
F1, F4, K8, A5, E1
High
I/O
BVSEL
WT
(3)
L2
Low
Output
BVSEL
V
DD
J9, J11, J13, J15, K10, K12, K14, L9, L11, L13, L15, M10, M12,
M14, N9, N11, N13, N15, P10, P12, P14
–
–
N/A
VDD_SENSE[0:1]
(17)
G11, J8
–
–
N/A
Table 17.
Pinout Listing for the PC7457, 483 CBGA Package (Continued)
相關PDF資料
PDF描述
PC7457VGU933N PowerPC 7457 RISC Microprocessor
PC74HC4016 SPST Analog Switch
PC74HCT4046A Phase-Locked Loop
PC74HCT4543 LCD Display Driver
PC74HCT7046A Phase-Locked Loop
相關代理商/技術參數
參數描述
PC7457VGU933N 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:PowerPC 7457 RISC Microprocessor
PC7457VGU933NC 制造商:e2v technologies 功能描述:PC7457VGU933NC - Trays
PC745B 制造商:Datak Corporation 功能描述:POTENTIOMETERS
PC745BMGH300LE 制造商:e2v technologies 功能描述:PC745BMGH300LE - Trays
PC745BMGH350LE 制造商:e2v technologies 功能描述:MPU RISC 32BIT 0.22UM 350MHZ 2.5V/3.3V 255HITCE CBGA - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*