參數資料
型號: PCA2002TK/1,118
廠商: NXP Semiconductors
文件頁數: 29/30頁
文件大小: 0K
描述: IC WATCH CIRCUIT 10HVSON
標準包裝: 6,000
類型: 時鐘/頻率發生器
PLL:
主要目的: 電池式腕表
輸入: 晶體
電路數: 1
比率 - 輸入:輸出: 1:2
差分 - 輸入:輸出: 無/無
頻率 - 最大: 32kHz
電源電壓: 1.1 V ~ 3.6 V
工作溫度: -10°C ~ 60°C
安裝類型: 表面貼裝
封裝/外殼: 10-VFDFN 裸露焊盤
供應商設備封裝: 10-HVSON(3x3)
包裝: 管件
其它名稱: 935275138118
PCA2002TK-T
PCA2002TK-T-ND
PCA2002
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 25 November 2011
8 of 30
NXP Semiconductors
PCA2002
32 kHz watch circuit with programmable output period and pulse width
8.6 Programming procedure
To ensure that the oscillator starts up correctly you must execute a reset sequence (see
For a watch it is essential that the timing calibration can be made after the watch is fully
assembled. In this situation, the supply pins are often the only terminals which are still
accessible.
Writing to the OTP cells and performing the related functional checks is achieved in the
PCA2002 by modulating the supply voltage. The necessary control circuit consists
basically of a voltage level detector, an instruction counter, which determines the function
to be performed, and an 8-bit shift register, which allows writing the OTP cells of an 8-bit
word in one step and which acts as data pointer for checking the OTP content.
State 1; measurement of the crystal oscillator frequency (divided by 1024)
State 2; measurement of the inhibition time
State 3; write/check word A
State 4; write/check word B
State 5; check word C (don’t care since no meaning)
State 6; check word D (type recognition)
Each instruction state is switched on with a pulse to VP(prog)(start). After this large pulse, an
initial waiting time of t0 is required. The programming instructions are then entered by
modulating the supply voltage with small pulses (amplitude VP(mod) and pulse width tmod).
The first small pulse defines the start time, the following pulses perform three different
functions, depending on the time delay (td) from the preceding pulse (see Figure 5,
td =t1 (0.7 ms); increments the instruction counter
td =t2 (1.7 ms); clocks the shift register with data = logic 0
td =t3 (2.7 ms); clocks the shift register with data = logic 1
The programming procedure requires a stable oscillator, which means that a waiting time,
determined by the start-up time of the oscillator, is necessary after power-up of the circuit.
td(start): start delay time.
VDD(nom): nominal supply voltage.
Fig 4.
Supply voltage at start-up during production and testing
VDD
VP(prog)(stop)
td(start) > 500 ms
VSS
VDD(nom)
001aac503
tp(stop)
相關PDF資料
PDF描述
PCKV857EV,118 IC 1:10 2.5V PLL CLK-DRVR48TSSOP
PCM1602APTG4 IC DAC 24BIT 6CH 192KHZ 48-LQFP
PCM1792DB IC 24BIT AUDIO STEREO DAC 28SSOP
PCM3168ATPAPQ1 IC 24-BIT AUDIO CODEC 64-HTQFP
PCM3168ATPAPRQ1G4 IC 24-BIT AUDIO CODEC 64-HTQFP
相關代理商/技術參數
參數描述
PCA2002TK-T 功能描述:馬達/運動/點火控制器和驅動器 WATCH IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
PCA2002U/10AA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:32 kHz watch circuit with programmable output period and pulse width
PCA2002U/10AB/1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:32 kHz watch circuit with programmable output period and pulse width
PCA2002U/10AB/1,00 功能描述:馬達/運動/點火控制器和驅動器 32KHZ WATCH CIRCUIT RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
PCA2002U/10AB/1,005 制造商:NXP Semiconductors 功能描述: