Remote 1" />
參數資料
型號： PCA8575PW,118
廠商： NXP Semiconductors
文件頁數： 28/30頁
文件大?。?/td> 0K
描述： IC I/O EXPANDER I2C 16B 24TSSOP
特色產品： NXP - I2C Interface
標準包裝： 1
接口： I²C
輸入/輸出數： 16
中斷輸出： 是
頻率 - 時鐘： 400kHz
電源電壓： 2.3 V ~ 5.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 24-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 24-TSSOP
包裝： 標準包裝
包括： POR
其它名稱： 568-8248-6
PCA8575_2
NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 02 — 21 March 2007
7 of 30
NXP Semiconductors
PCA8575
Remote 16-bit I/O expander for I2C-bus with interrupt
8.
I/O programming
8.1 Quasi-bidirectional I/O architecture
The PCA8575’s 16 ports (see Figure 2) are entirely independent and can be used either
as input or output ports. Input data is transferred from the ports to the microcontroller in
the Read mode (see Figure 12). Output data is transmitted to the ports in the Write mode
Every data transmission from the PCA8575 must consist of an even number of bytes, the
rst byte will be referred to as P07 to P00, and the second byte as P17 to P10. The third
will be referred to as P07 to P00, and so on.
This quasi-bidirectional I/O can be used as an input or output without the use of a control
signal for data directions. At power-on the I/Os are HIGH. In this mode only a current
source (IOH) to VDD is active. An additional strong pull-up to VDD (Itrt(pu)) allows fast rising
edges into heavily loaded outputs. These devices turn on when an output is written HIGH,
and are switched off by the negative edge of SCL. The I/Os should be HIGH before being
used as inputs. After power-on, as all the I/Os are set HIGH, all of them can be used as
inputs. Any change in setting of the I/Os as either inputs or outputs can be done with the
Write mode.
Remark: If a HIGH is applied to an I/O which has been written earlier to LOW, a large
current (IOL) will ow to VSS.
8.2 Writing to the port (Output mode)
To write, the master (microcontroller) rst addresses the slave device. By setting the last
bit of the byte containing the slave address to logic 0 the Write mode is entered. The
PCA8575 acknowledges and the master sends the rst data byte for P07 to P00. After the
rst data byte is acknowledged by the PCA8575, the second data byte P17 to P10 is sent
by the master. Once again, the PCA8575 acknowledges the receipt of the data. Each 8-bit
data is presented on the port lines after it has been acknowledged by the PCA8575.
The number of data bytes that can be sent successively is not limited. After every two
bytes, the previous data is overwritten.
The rst data byte in every pair refers to Port 0 (P07 to P00), whereas the second data
byte in every pair refers to Port 1 (P17 to P10). See Figure 10.
Fig 10. Correlation between bits and ports
A
002aab634
06
05
04
03
02
01
00
first byte
07
P06 P05 P04 P03 P02 P01 P00
P07
A
16
15
14
13
12
11
10
second byte
17
P16 P15 P14 P13 P12 P11 P10
P17
相關PDF資料
PDF描述
PCA9502BS,151 IC I/O EXPANDER I2C/SPI 24HVQFN
PCA9501D,118 IC I/O EXPANDER I2C 8B 20SOIC
ATTINY44A-CCUR MCU AVR 4KB FLASH 20MHZ 15UFBGA
2-583717-7 CONN CARD EDGE 14POS .100 PCB
ATTINY2313A-SUR MCU AVR 2KB FLASH 20MHZ 20SOIC
相關代理商/技術參數
參數描述
PCA8576C 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal LCD driver for low multiplex rates
PCA8576CH/Q900,157 功能描述:LCD 驅動器 UNIVERSAL LCD DRIVER LOW MULTIPLEX RATES RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
PCA8576CH/Q900/1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal LCD driver for low multiplex rates
PCA8576CH/Q900/1,1 功能描述:LCD 驅動器 MULT DIG/SEG 200KHz RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
PCA8576CH/Q900/1,118 制造商:NXP Semiconductors 功能描述:Cut Tape 制造商:NXP Semiconductors 功能描述:0
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*