- 您現在的位置：買賣IC網 > PDF目錄3777 > PCA9507DP,118 (NXP Semiconductors)IC I/O EXPANDER I2C 24B 8TSSOP PDF資料下載
參數資料
| 型號： | PCA9507DP,118 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 17/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER I2C 24B 8TSSOP |
| 產品培訓模塊： | I²C Bus Fundamentals |
| 特色產品： | NXP - I2C Interface |
| 標準包裝： | 1 |
| 接口： | I²C，SM 總線 |
| 輸入/輸出數： | 2 輸入，2 輸出 |
| 中斷輸出： | 無 |
| 頻率 - 時鐘： | 400kHz |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-TSSOP |
| 包裝： | 標準包裝 |
| 其它名稱： | 568-5924-6 |
PCA9507_1
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 01 — 7 February 2008
6 of 20
NXP Semiconductors
PCA9507
2-wire serial bus extender for HDMI DDC I2C-bus and SMBus
6.3.2 Port B (SDAB and SCLB)
SDAB and SCLB are standard I2C-bus with static level offset that has no rise time
accelerator. The static level offset produces an output LOW of 0.5 V (typical) at 6 mA. As
with the standard I2C-bus system, pull-up resistors are required to provide the logic HIGH
levels. The size of these pull-up resistors depends on the system requirement, and should
meet the current sinking capability of the device that drives the buffer, as well as that of
the buffer. The minimum and maximum pull-up resistors are determined and the pull-up
resistor’s value is chosen to be within the minimum and maximum range.
Using Equation 1, calculate the minimum pull-up resistor value:
(1)
Where:
RPU(min) is the minimum pull-up resistor value for the open-drain SCLB and SDAB.
VCC(B)(max) is the maximum supply rail of the pull-up resistor.
0.4 V is the maximum VOL of the device that drives the buffer on logic LOW.
IOL(max) at VOL = 0.4 V is the maximum sink current of the device that drives the buffer
on logic LOW.
The maximum pull-up resistor should also be sized such that the RC time constant meets
the standard I2C-bus rise time, which is 1
s for Standard-mode (100 kHz) or 300 ns for
Fast-mode (400 kHz). DDC bus complies with the I2C-bus Standard-mode and operates
below 100 kHz, and maximum rise time is 1
s using a simplied RC equation.
Using Equation 2, calculate the maximum pull-up resistor value:
(2)
Where:
RPU(max) is the maximum allowable pull-up resistor on the SCLB and SDAB in order to
meet the I2C-bus rise time specication.
CL(max) is the maximum allowable capacitance load (include the capacitance of driver,
the line, and the buffer) in order to meet the rise time specication.
tr is the rise time specied as 1 s (for bus speed 100 kHz or lower) and 300 ns (for bus
speed 400 kHz or lower).
The chosen pull-up resistor RPU is: RPU(min) ≤ RPU ≤ RPU(max).
R
PU min
()
V
CC B
() max
()
0.4 V
–
I
OL max
()
-------------------------------------------------
=
R
PU max
()
C
L max
()
×
1.2
t
r
×
=
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9670PW,112 | IC I/O EXPANDER I2C 8B 16TSSOP |
| PCA9574BS,118 | IC I/O EXPANDER I2C 8B 16HVQFN |
| ATTINY24A-MUR | MCU AVR 2KB FLASH 20MHZ 20QFN |
| PCA8574PW,118 | IC I/O EXPANDER I2C 8B 16TSSOP |
| ATTINY24A-CCUR | MCU AVR 2KB FLASH 20MHZ 15UFBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9507DP-T | 功能描述:接口-信號緩沖器、中繼器 LEVEL TRANSL I2C BUS REPEATER RoHS:否 制造商:Texas Instruments 工作電源電壓: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:VSSOP-8 封裝:Reel |
| PCA9507D-T | 功能描述:接口-信號緩沖器、中繼器 LEVEL TRANSL I2C BUS REPEATER RoHS:否 制造商:Texas Instruments 工作電源電壓: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:VSSOP-8 封裝:Reel |
| PCA9508 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Smart, simple solutions for the 12 most common design concerns |
| PCA9508D | 功能描述:接口-信號緩沖器、中繼器 HOTSWAP LVTTL I2C-BUS REPEATER RoHS:否 制造商:Texas Instruments 工作電源電壓: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:VSSOP-8 封裝:Reel |
| PCA9508D,112 | 功能描述:接口-信號緩沖器、中繼器 HOTSWAP LVTTL RoHS:否 制造商:Texas Instruments 工作電源電壓: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:VSSOP-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。