參數資料
| 型號： | PCA9535D,118 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 25/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER I2C 16B 24SOIC |
| 特色產品： | NXP - I2C Interface |
| 標準包裝： | 1 |
| 接口： | I²C，SM 總線 |
| 輸入/輸出數： | 16 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 400kHz |
| 電源電壓： | 2.3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SO |
| 包裝： | * |
| 包括： | POR |
| 其它名稱： | 568-8708-6 |
PCA9535_PCA9535C_5
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 15 September 2008
8 of 31
NXP Semiconductors
PCA9535; PCA9535C
16-bit I2C-bus and SMBus, low power I/O port with interrupt
6.2.5 Registers 6 and 7: Conguration registers
This register congures the directions of the I/O pins. If a bit in this register is set (written
with ‘1’), the corresponding port pin is enabled as an input with high-impedance output
driver. If a bit in this register is cleared (written with ‘0’), the corresponding port pin is
enabled as an output. At reset, the device's ports are inputs.
6.3 Power-on reset
When power is applied to VDD, an internal power-on reset holds the PCA9535/PCA9535C
in a reset condition until VDD has reached VPOR. At that point, the reset condition is
released and the PCA9535/PCA9535C registers and SMBus state machine will initialize
to their default states. Thereafter, VDD must be lowered below 0.2 V to reset the device.
For a power reset cycle, VDD must be lowered below 0.2 V and then restored to the
operating voltage.
6.4 I/O port
When an I/O is congured as an input on PCA9535, FETs Q1 and Q2 are off, creating a
high impedance input. The input voltage may be raised above VDD to a maximum of 5.5 V.
In the case of PCA9535C, FET Q1 has been removed and the open-drain FET Q2 will
function the same as PCA9535.
If the I/O is congured as an output, then on PCA9535 either Q1 or Q2 is on, depending
on the state of the Output Port register. Care should be exercised if an external voltage is
applied to an I/O congured as an output because of the low-impedance path that exists
between the pin and either VDD or VSS.
Table 11.
Conguration port 0 register
Bit
7
6
5
4
3
2
1
0
Symbol
C0.7
C0.6
C0.5
C0.4
C0.3
C0.2
C0.1
C0.0
Default
11111111
Table 12.
Conguration port 1 register
Bit
7
6
5
4
3
2
1
0
Symbol
C1.7
C1.6
C1.5
C1.4
C1.3
C1.2
C1.1
C1.0
Default
11111111
相關PDF資料 |
PDF描述 |
|---|---|
| 292204-2 | CONN CARD EDGE 8POS DL 2MM TIN |
| ATTINY44V-10SSUR | MCU AVR 4KB FLASH 10MHZ 14-SOIC |
| ATTINY24-20MUR | MCU AVR 2KB FLASH 20MHZ 20QFN |
| ATTINY24V-10MUR | MCU AVR 2KB FLASH 10MHZ 20QFN |
| PCA9675PW,112 | IC I/O EXPANDER I2C 16B 24TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9535DB | 功能描述:接口-I/O擴展器 16-Bit I2C & SMBus Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9535DBG4 | 功能描述:接口-I/O擴展器 Rem 16B I2C & SMBus Low-Pwr I/O Exp RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9535DBQR | 功能描述:接口-I/O擴展器 16-Bit I2C & SMBus Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9535DBQRG4 | 功能描述:接口-I/O擴展器 16-Bit I2C & SMBus Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9535DBR | 功能描述:接口-I/O擴展器 16-Bit I2C & SMBus Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。