參數資料
型號： PCA9538BS,118
廠商： NXP Semiconductors
文件頁數： 33/34頁
文件大小： 0K
描述： IC I/O EXPANDER I2C 8B 16HVQFN
產品培訓模塊： I²C Bus Fundamentals
特色產品： NXP - I2C Interface
標準包裝： 1
接口： I²C，SM 總線
輸入/輸出數： 8
中斷輸出： 是
頻率 - 時鐘： 400kHz
電源電壓： 2.3 V ~ 5.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 16-VQFN 裸露焊盤
供應商設備封裝： 16-HVQFN
包裝： 標準包裝
包括： POR
產品目錄頁面： 825 (CN2011-ZH PDF)
配用： 568-3615-ND - DEMO BOARD I2C
其它名稱： 568-1838-6
PCA9538
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 6 — 6 February 2013
8 of 34
NXP Semiconductors
PCA9538
8-bit I2C-bus and SMBus low power I/O port with interrupt and reset
6.2.5 Register 3 - Configuration register
This register configures the directions of the I/O pins. If a bit in this register is set, the
corresponding port pin is enabled as an input with high-impedance output driver. If a bit in
this register is cleared, the corresponding port pin is enabled as an output. At reset, the
I/Os are configured as inputs.
6.3 Power-on reset
When power is applied to VDD, an internal Power-On Reset (POR) holds the PCA9538 in
a reset condition until VDD has reached VPOR. At that point, the reset condition is released
and the PCA9538 registers and state machine will initialize to their default states.
Thereafter, VDD must be lowered below 0.2 V to reset the device.
For a power reset cycle, VDD must be lowered below 0.2 V and then restored to the
operating voltage.
6.4 RESET input
A reset can be accomplished by holding the RESET pin LOW for a minimum of tw(rst).
The PCA9538 registers and SMBus/I2C-bus state machine will be held in their default
state until the RESET input is once again HIGH. This input requires a pull-up resistor to
VDD if no active connection is used.
6.5 Interrupt output
The open-drain interrupt output (INT) is activated when one of the port pins changes state
and the pin is configured as an input. The interrupt is de-activated when the input returns
to its previous state or the Input Port register is read.
Note that changing an I/O from an output to an input may cause a false interrupt to occur
if the state of the pin does not match the contents of the Input Port register.
Table 8.
Register 3 - Configuration register bit description
Legend: * default value.
Bit
Symbol
Access
Value
Description
7
C7
R/W
1*
configures the directions of the I/O pins
0 = corresponding port pin enabled as an output
1 = corresponding port pin configured as an input
(default value)
6C6
R/W
1*
5C5
R/W
1*
4C4
R/W
1*
3C3
R/W
1*
2C2
R/W
1*
1C1
R/W
1*
0C0
R/W
1*
相關PDF資料
PDF描述
TC030090BH10236BJ1 CAP CER 10KVP 1000PF +/-10% R85
VI-2WY-IY CONVERTER MOD DC/DC 3.3V 33W
MS3102E22-2PW CONN RCPT 3POS BOX MNT W/PINS
MPC565MVR56 IC MCU 1M FLASH 56MHZ 388-BGA
MS3100A14S-2P CONN RCPT 4POS WALL MNT W/PINS
相關代理商/技術參數
參數描述
PCA9538D 功能描述:接口-I/O擴展器 8-BIT I2C FM TP GPIO INT RST RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9538D,112 功能描述:接口-I/O擴展器 8-BIT I2C FM TP GPIO RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9538D,118 功能描述:接口-I/O擴展器 I2C/SMBUS 8BIT GPIO RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9538DB 功能描述:接口-I/O擴展器 Rem 8B I2C & SMBus Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9538DBG4 功能描述:接口-I/O擴展器 Rem 8B I2C & SMBus Lo-Pwr I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*