參數資料
型號: PCA9539RPW,112
廠商: NXP Semiconductors
文件頁數: 36/37頁
文件大?。?/td> 0K
描述: IC I/O EXPANDER I2C 16B 24TSSOP
標準包裝: 1,575
接口: I²C,SM 總線
輸入/輸出數: 16
中斷輸出:
頻率 - 時鐘: 400kHz
電源電壓: 2.3 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 24-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 24-TSSOP
包裝: 管件
包括: POR
其它名稱: 935286605112
PCA9539RPW
PCA9539RPW-ND
PCA9539_PCA9539R
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 6 — 6 February 2013
8 of 37
NXP Semiconductors
PCA9539; PCA9539R
16-bit I2C-bus and SMBus low power I/O port with interrupt and reset
6.2.5 Registers 6 and 7: Configuration registers
This register configures the directions of the I/O pins. If a bit in this register is set (written
with ‘1’), the corresponding port pin is enabled as an input with high-impedance output
driver. If a bit in this register is cleared (written with ‘0’), the corresponding port pin is
enabled as an output. At reset, the device's ports are inputs.
6.3 Power-on reset
When power is applied to VDD, an internal power-on reset holds the PCA9539; PCA9539R
in a reset condition until VDD has reached VPOR. At that point, the reset condition is
released and the PCA9539; PCA9539R registers and SMBus state machine will initialize
to their default states. Thereafter, VDD must be lowered below 0.2 V to reset the device.
For a power reset cycle, VDD must be lowered below 0.2 V and then restored to the
operating voltage.
6.4 RESET input
A reset can be accomplished by holding the RESET pin LOW for a minimum of tw(rst). In
the PCA9539 the registers and SMBus/I2C-bus state machine will be held in their default
state until the RESET input is once again HIGH. This input typically requires a pull-up to
VDD. In the PCA9539R, only the device state machine is initialized. The internal
general-purpose registers remain unchanged. Using the PCA9539R hardware reset pin
will only reset the I2C-bus interface should it be stuck LOW to regain access to the
I2C-bus. This allows the I/O pins to retain their last configured state so that they can keep
any lines in their previously defined state and not cause system errors while the I2C-bus is
being restored.
6.5 I/O port
When an I/O is configured as an input, FETs Q1 and Q2 are off, creating a
high-impedance input. The input voltage may be raised above VDD to a maximum of 5.5 V.
If the I/O is configured as an output, then either Q1 or Q2 is on, depending on the state of
the Output port register. Care should be exercised if an external voltage is applied to an
I/O configured as an output because of the low-impedance path that exists between the
pin and either VDD or VSS.
Table 11.
Configuration port 0 register
Bit
7
6
5
4
3
2
1
0
Symbol
C0.7
C0.6
C0.5
C0.4
C0.3
C0.2
C0.1
C0.0
Default
11
Table 12.
Configuration port 1 register
Bit
7
6
5
4
3
2
1
0
Symbol
C1.7
C1.6
C1.5
C1.4
C1.3
C1.2
C1.1
C1.0
Default
11
相關PDF資料
PDF描述
PCA9554TS,112 IC I/O EXPANDER I2C 8B 20SSOP
PCA9555N,112 IC I/O EXPANDER I2C 16B 24DIP
PCA9556PW,112 IC I/O EXPANDER I2C 8B 16TSSOP
PCA9557D/DG,118 IC I/O PORT I2C/SMBUS 16-SOIC
PCA9574HR,115 IC I/O EXPANDER I2C 8B 16HXQFN
相關代理商/技術參數
參數描述
PCA9540 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-channel I2C multiplexer
PCA9540B 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-channel I2C-bus multiplexer
PCA9540BD 功能描述:編碼器、解碼器、復用器和解復用器 I2C MUX 2CH BI-DIR RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量(輸入/輸出):2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
PCA9540BD,112 功能描述:編碼器、解碼器、復用器和解復用器 I2C MUX 2CH BI-DIR RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量(輸入/輸出):2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
PCA9540BD,118 功能描述:編碼器、解碼器、復用器和解復用器 2-CHANNEL I2C MULTIPLEXER RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量(輸入/輸出):2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray