參數資料
型號: PCA9671D,118
廠商: NXP Semiconductors
文件頁數: 2/33頁
文件大?。?/td> 0K
描述: IC I/O EXPANDER I2C 16B 24SOIC
產品培訓模塊: LED Controllers
I²C Bus Fundamentals
特色產品: NXP - I2C Interface
標準包裝: 1
接口: I²C
輸入/輸出數: 16
中斷輸出:
頻率 - 時鐘: 1MHz
電源電壓: 2.3 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 24-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 24-SO
包裝: 標準包裝
包括: POR
產品目錄頁面: 826 (CN2011-ZH PDF)
其它名稱: 568-4192-6
PCA9671
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 3 — 29 September 2011
10 of 33
NXP Semiconductors
PCA9671
Remote 16-bit I/O expander for Fm+ I2C-bus with reset
7.2.2 Device ID (PCA9671 ID field)
The Device ID field is a 3-byte read-only (24 bits) word giving the following information:
8 bits with the manufacturer name, unique per manufacturer (for example,
NXP Semiconductors).
13 bits with the part identification, assigned by manufacturer, the 7 MSBs with the
category ID and the 6 LSBs with the feature ID (for example, PCA9671 16-bit
quasi-output I/O expander).
3 bits with the die revision, assigned by manufacturer (for example, Rev X).
The Device ID is read-only, hardwired in the device and can be accessed as follows:
1. START command.
2. The master sends the Reserved Device ID I2C-bus address ‘1111 100’ with the R/W
bit set to logic 0 (write).
3. The master sends the I2C-bus slave address of the slave device it needs to identify.
The LSB is a ‘Don’t care’ value. Only one device must acknowledge this byte (the one
that has the I2C-bus slave address).
4. The master sends a Re-START command.
Remark: A STOP command followed by a START command will reset the slave state
machine and the Device ID read cannot be performed.
Remark: A STOP command or a Re-START command followed by an access to
another slave device will reset the slave state machine and the Device ID read cannot
be performed.
5. The master sends the Reserved Device ID I2C-bus address ‘1111 100’ with the R/W
bit set to logic 1 (read).
6. The device ID read can be done, starting with the 8 manufacturer bits (first byte +
4 MSB of the second byte), followed by the 13 part identification bits and then the
3 die revision bits (3 LSB of the third byte).
7. The master ends the reading sequence by NACKing the last byte, thus resetting the
slave device state machine and allowing the master to send the STOP command.
Remark: The reading of the Device ID can be stopped anytime by sending a NACK
command.
Remark: If the master continues to ACK the bytes after the third byte, the PCA9671
rolls back to the first byte and keeps sending the Device ID sequence until a NACK
has been detected.
For the PCA9671, the Device ID is as shown in Figure 11.
相關PDF資料
PDF描述
616-220-310 UNIGUIDE 9" X .141" GREY
3448-58 STRAIN RELIEF 50 POS
3448-56 STRAIN RELIEF 34 POS
MAX7325ATG+ IC I/O EXPANDER I2C 8B 24TQFN-EP
3448-54 STRAIN RELIEF 20 POS
相關代理商/技術參數
參數描述
PCA9671DB 功能描述:接口-I/O擴展器 16-BIT I2C FM+ QB GPIO RST PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9671DB,112 功能描述:接口-I/O擴展器 16-BIT I2C FM+ QB RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9671DB,118 功能描述:接口-I/O擴展器 16-BIT I2C FM+ QB RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9671DB-T 功能描述:接口-I/O擴展器 16-BIT I2C FM+ QB GPIO RST PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9671DK,118 功能描述:接口-I/O擴展器 16-BIT I2C FM+ QB RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel