參數資料
型號: PCA9672BS,118
廠商: NXP Semiconductors
文件頁數: 34/36頁
文件大?。?/td> 0K
描述: IC I/O EXPANDER 8BIT 16-HVQFN
標準包裝: 1
接口: I²C
輸入/輸出數: 8
中斷輸出:
頻率 - 時鐘: 1MHz
電源電壓: 2.3 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 16-VFQFN 裸露焊盤
供應商設備封裝: 16-HVQFN
包裝: 標準包裝
包括: POR
其它名稱: 568-4194-6
PCA9672
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 3 — 27 May 2013
7 of 36
NXP Semiconductors
PCA9672
Remote 8-bit I/O expander for Fm+ I2C-bus with interrupt and reset
7.2.1 Software Reset
The Software Reset Call allows all the devices in the I2C-bus to be reset to the power-up
state value through a specific formatted I2C-bus command. To be performed correctly, it
implies that the I2C-bus is functional and that there is no device hanging the bus.
The Software Reset sequence is defined as following:
1. A START command is sent by the I2C-bus master.
2. The reserved General Call I2C-bus address ‘0000 000’ with the R/W bit set to 0 (write)
is sent by the I2C-bus master.
3. The PCA9672 device(s) acknowledge(s) after seeing the General Call address
‘0000 0000’ (00h) only. If the R/W bit is set to 1 (read), no acknowledge is returned to
the I2C-bus master.
4. Once the General Call address has been sent and acknowledged, the master sends
1 byte. The value of the byte must be equal to 06h.
a. The PCA9672 acknowledges this value only. If the byte is not equal to 06h, the
PCA9672 does not acknowledge it.
If more than 1 byte of data is sent, the PCA9672 does not acknowledge any more.
5. Once the right byte has been sent and correctly acknowledged, the master sends a
STOP command to end the Software Reset sequence: the PCA9672 then resets to
the default value (power-up value) and is ready to be addressed again within the
specified bus free time. If the master sends a Repeated START instead, no reset is
performed.
The I2C-bus master must interpret a non-acknowledge from the PCA9672 (at any time) as
a ‘Software Reset Abort’. The PCA9672 does not initiate a reset of its registers.
The unique sequence that initiates a Software Reset is described in Figure 9.
Simple code for Software Reset:
<S> <00h> <ACK> <06h> <ACK> <P>
Fig 9.
Software Reset sequence
002aac329
0
A
S
0
SWRST Call I2C-bus address
START condition
R/W
acknowledge
from slave(s)
0
1
0
SWRST data = 06h
A
acknowledge
from slave(s)
P
PCA9672 is(are) reset.
Registers are set to default power-up values.
相關PDF資料
PDF描述
2-583859-1 CONN CARDEDGE HSNG 8POS DL .156
530509-8 CONN HOUSING 18POS W/MT EARS
PCA9674ABS,118 IC I/O EXPANDER I2C 8B 16HVQFN
583861-1 TW-LF CRP HSG 30 POS
583617-1 HSG AMP LEAF 22 POS
相關代理商/技術參數
參數描述
PCA9672BS-T 功能描述:接口-I/O擴展器 8BIT I2C FM+ QB GPIO INT-RS PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9672D 功能描述:接口-I/O擴展器 8BIT I2C FM+ QB GPIO INT-RS PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9672D,512 功能描述:接口-I/O擴展器 8BIT I2C FM+ QB GPIO RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9672D,518 功能描述:接口-I/O擴展器 8BIT I2C FM+ QB GPIO RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9672D-T 功能描述:接口-I/O擴展器 8BIT I2C FM+ QB GPIO INT-RS PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel