參數資料
型號： PCA9674A
廠商： NXP Semiconductors N.V.
英文描述： Remote 8-bit I/O expander for Fm+ I2C-bus with interrupt
中文描述： 遠程8位I / O擴展調頻I2C總線的中斷
文件頁數： 11/34頁
文件大?。?/td> 179K
代理商： PCA9674A
PCA9674_PCA9674A_2
NXP B.V. 2006. All rights reserved.
Product data sheet
Rev. 02 — 12 October 2006
11 of 34
NXP Semiconductors
PCA9674/74A
Remote 8-bit I/O expander for Fm+ I
2
C-bus with interrupt
7.2.1
Software Reset
The Software Reset Call allows all the devices in the I
2
C-bus to be reset to the power-up
state value through a specific formatted I
2
C-bus command. To be performed correctly, it
implies that the I
2
C-bus is functional and that there is no device hanging the bus.
The Software Reset sequence is defined as following:
1. A START command is sent by the I
2
C-bus master.
2. The reserved General Call I
2
C-bus address ‘0000 000’ with the R/W bit set to 0 (write)
is sent by the I
2
C-bus master.
3. The PCA9674/74A device(s) acknowledge(s) after seeing the General Call address
‘0000 0000’ (00h) only. If the R/W bit is set to 1 (read), no acknowledge is returned to
the I
2
C-bus master.
4. Once the General Call address has been sent and acknowledged, the master sends
1 byte. The value of the byte must be equal to 06h.
a. The PCA9674/74A acknowledges this value only. If the byte is not equal to 06h, the
PCA9674/74A does not acknowledge it.
If more than 1 byte of data is sent, the PCA9674/74A does not acknowledge any
more.
5. Once the right byte has been sent and correctly acknowledged, the master sends a
STOP command to end the Software Reset sequence: the PCA9674/74A then resets
to the default value (power-up value) and is ready to be addressed again within the
specified bus free time. If the master sends a Repeated START instead, no reset is
performed.
The I
2
C-bus master must interpret a non-acknowledge from the PCA9674/74A (at any
time) as a ‘Software Reset Abort’. The PCA9674/74A does not initiate a reset of its
registers.
The unique sequence that initiates a Software Reset is described in
Figure 11
.
Fig 10. Device ID address
R/W
002aac116
1
1
1
1
1
0
0
Fig 11. Software Reset sequence
002aac262
0
0
0
0
0
0
0
A
S
0
SWRST Call I
2
C-bus address
START condition
R/W
acknowledge
from slave(s)
0
0
0
0
1
1
0
0
SWRST data = 06h
A
acknowledge
from slave(s)
P
PCA9674/74A is(are) reset.
Registers are set to default power-up values.
相關PDF資料
PDF描述
PCA9675 Remote 16-bit I/O expander for Fm+ I2C-bus with interrupt
PCA9675DB Remote 16-bit I/O expander for Fm+ I2C-bus with interrupt
PCA9675DK Remote 16-bit I/O expander for Fm+ I2C-bus with interrupt
PCA9698 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT
PCADADIO-CS PC(ISA)BUS I/O CARD
相關代理商/技術參數
參數描述
PCA9674ABS,118 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9674ABS,118-CUT TAPE 制造商:NXP 功能描述:PCA9674 Series 1 MHz 8 bit I/O Expander Fm + I2C Bus with Interrupt - HVQFN-16
PCA9674ABS-T 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB GPIO RST PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9674AD 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB GPIO INT PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9674AD,512 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*