Remote 16-bit I/O expander for I2
參數資料
型號： PCF8575TS/1,112
廠商： NXP Semiconductors
文件頁數： 3/24頁
文件大小： 0K
描述： IC I/O EXPANDER I2C 16B 24SSOP
產品培訓模塊： I²C Bus Fundamentals
特色產品： NXP - I2C Interface
標準包裝： 59
接口： I²C
輸入/輸出數： 16
中斷輸出： 是
頻率 - 時鐘： 400kHz
電源電壓： 4.5 V ~ 5.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 24-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 24-SSOP
包裝： 管件
包括： POR
產品目錄頁面： 827 (CN2011-ZH PDF)
其它名稱： 568-3989-5
935276552112
PCF8575TSDB
PCF8575TSDB-ND
1999 Apr 07
11
Philips Semiconductors
Product specication
Remote 16-bit I/O expander for I2C-bus
PCF8575
7.3
Reading from a port (input mode)
All ports programmed as input should be set to logic 1.
To read, the master (microcontroller) first addresses the
slave device after it receives the interrupt. By setting the
last bit of the byte containing the slave address to logic 1
the read mode is entered. The data bytes that follow on the
SDA are the values on the ports.
If the data on the input port changes faster than the master
can read, this data may be lost.
7.4
Writing to the port (output mode)
To write, the master (microcontroller) first addresses the
slave device. By setting the last bit of the byte containing
the slave address to logic 0 the write mode is entered.
The PCF8575 acknowledges and the master sends the
first data byte for P07 to P00. After the first data byte is
acknowledged by the PCF8575, the second data byte
P17 to P10 is sent by the master. Once again the
PCF8575 acknowledges the receipt of the data after which
this 16-bit data is presented on the port lines.
The number of data bytes that can be sent successively is
not limited. After every two bytes the previous data is
overwritten.
The first data byte in every pair refers to Port 0
(P07 to P00), whereas the second data byte in every pair
refers to Port 1 (P17 to P10), see Fig.11.
7.5
Interrupt
The PCF8575 provides an open-drain interrupt (INT)
which can be fed to a corresponding input of the
microcontroller (see Figs 9, 10 and 12). This gives these
chips a kind of a master function which can initiate an
action elsewhere in the system.
An interrupt is generated by any rising or falling edge of the
port inputs. After time tiv the signal INT is valid.
The interrupt disappears when data on the port is changed
to the original setting or data is read from or written to the
device which has generated the interrupt.
In the write mode the interrupt may become deactivated
(HIGH) on the rising edge of the write to port pulse. On the
falling edge of the write to port pulse the interrupt is
definitely deactivated (HIGH).
The interrupt is reset in the read mode on the rising edge
of the read from port pulse.
During the resetting of the interrupt itself any changes on
the I/Os may not generate an interrupt. After the interrupt
is reset any change in I/Os will be detected and transmitted
as an INT.
Fig.11 Correlation between bits and ports.
handbook, full pagewidth
MGL545
07
06
05
04
03
02
01
00
P07 P06 P05 P04 P03 P02 P01 P00
A
First Byte
17
16
15
14
13
12
11
10
P17 P16 P15 P14 P13 P12 P11 P10
A
Second Byte
相關PDF資料
PDF描述
PCI7620ZHK IC 2SLT PC CARD/SC CTLR 288-PBGA
PCX7447AVGH1167NB IC MPU 32BIT 1167MHZ 360CBGA
PEB1756E IC MUX/DEMUX STS192/STM64 1397CB
PEB1757E IC MUX/DEMUX STS192/STM64 1397CB
PI2DBS212ZHEX IC MUX/DEMUX 2X1 28TQFN
相關代理商/技術參數
參數描述
PCF8575TSDB 制造商:NXP Semiconductors 功能描述:I2C GPIO Expander 5.5V 24-Pin SSOP Tube
PCF8575TSDB-T 制造商:NXP Semiconductors 功能描述:
PCF8576 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal LCD driver for low multiplex rates
PCF8576_01 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal LCD driver for low multiplex rates
PCF8576C 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal LCD driver for low multiplex rates
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*