- 您現在的位置：買賣IC網 > PDF目錄367822 > PCK2001 (NXP Semiconductors N.V.) 14.318-150 MHz I 2 C 1:18 Clock Buffer(14.318-150 MHz IIC 1:18時鐘緩沖器) PDF資料下載
參數資料
| 型號： | PCK2001 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 14.318-150 MHz I 2 C 1:18 Clock Buffer(14.318-150 MHz IIC 1:18時鐘緩沖器) |
| 中文描述： | 14.318-150兆赫的I 2 C 1:18時鐘緩沖器（14.318-150兆赫進口證1:18時鐘緩沖器） |
| 文件頁數： | 9/13頁 |
| 文件大?。?/td> | 80K |
| 代理商： | PCK2001 |
Philips Semiconductors
Product specification
PCK2001
14.318–150 MHz I
2
C 1:18 Clock Buffer
1999 Jul 06
9
Consider the command code and the byte count bytes required as the first two bytes of any transfer. The command code is software
programmable via the controller, but will be specified as 0000 0000 in the clock specification. The byte count byte is the number of additional
bytes required to transfer, not counting the command code and byte count bytes. Additionally, the byte count byte is required to be a minimum of
1 byte and a maximum of 32 bytes to satisfy the above requirement.
For example:
Byte count byte
Notes:
MSB
LSB
0000
0000
Not allowed. Must have at least one byte.
0000
0001
Data for functional and frequency select register (currently byte 0 in spec)
0000
0010
Reads first two bytes of data. (byte 0 then byte 1)
0000
0011
Reads first three bytes (byte 0, 1, 2 in order)
0000
0100
Reads first four bytes (byte 0, 1, 2, 3 in order)
0000
0101
Reads first five bytes (byte 0, 1, 2, 3, 4 in order)
0000
0110
Reads first six bytes (byte 0, 1, 2, 3, 4, 5 in order)
0000
0111
Reads first seven bytes (byte 0, 1, 2, 3, 4, 5, 6 in order)
0010
0000
Max byte count supported = 32
A transfer is considered valid after the acknowledge bit corresponding to the byte count is read by the controller. The serial controller interface
can be simplified by discarding the information in both the command code and the byte count bytes and simply reading all the bytes that are
sent to the clock driver after being addressed by the controller. It is expected that the controller will not provide more bytes than the clock driver
can handle. A clock vendor may choose to discard any number of bytes that exceed the defined byte count.
8) Clock stretching: The clock device must not hold/stretch the SCLOCK or SDATA lines low for more than 10 mS. Clock stretching is
discouraged and should only be used as a last resort. Stretching the clock/data lines for longer than this time puts the device in an error/time-out
mode and may not be supported in all platforms. It is assumed that all data transfers can be completed as specified without the use of
clock/data stretching.
9) General Call: It is assumed that the clock driver will not have to respond to the ‘‘general call.”
10) Electrical Characteristics: All electrical characteristics must meet the standard mode specifications found in section 15 of the I
2
C
specification.
a) Pull-Up Resistors: Any internal resistors pull-ups on the SDATA and SCLOCK inputs must be stated in the individual datasheet. The use of
internal pull-ups on these pins of below 100K is discouraged. Assume that the board designer will use a single external pull-up resistor for each
line and that these values are in the 5 - 6K Ohm range. Assume one I
2
C device per DIMM (serial presence detect), one I
2
C controller, one clock
driver plus one/two more I
2
C devices on the platform for capacitive loading purposes.
(b) Input Glitch Filters: Only fast mode I
2
C devices require input glitch filters to suppress bus noise. The clock driver is specified as a standard
mode device and is not required to support this feature.
11) PWR DWN#: If a clock driver is placed in PWR DWN# mode, the SDATA and SCLK inputs must be Tri-Stated and the device must retain all
programming information. I
dd
current due to the I
2
C circuitry must be characterized and in the data sheet.
For specific I
2
C information consult the Philips I
2
C Peripherals Data Handbook IC12 (1997)
相關PDF資料 |
PDF描述 |
|---|---|
| PCK2010RDL | CONN 622-5030 T&B |
| PCK2010R | CK98R (100/133MHz) RCC Spread Spectrum System Clock Generator(CK98 (100/133MHz)RCC 擴散光譜系統時鐘發生器) |
| PCK2010 | CK98 (100/133MHz) Spread Spectrum System Clock Generator(CK98 (100/133MHz) 擴散光譜系統始終發生器) |
| PCK2010DL | CK98 100/133MHz Spread Spectrum System Clock Generator |
| PCK2010RA | CK98R 100/133MHz RCC spread spectrum system clock generator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCK2001DL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:14.318-150 MHz I2C 1:18 Clock Buffer |
| PCK2001DL,112 | 功能描述:時鐘緩沖器 PII CLOCK DRIVER RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| PCK2001DL,118 | 功能描述:時鐘緩沖器 PII CLOCK DRIVER RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| PCK2001DL-T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Eighteen Distributed-Output Clock Driver |
| PCK2001M | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:14.318-150 MHz I2C 1:10 Clock Buffer |
發布緊急采購，3分鐘左右您將得到回復。