- 您現在的位置：買賣IC網 > PDF目錄369952 > PCM3060 24-BIT, 96/192-kHz ASYNCHRONOUS STEREO AUDIO CODEC PDF資料下載
參數資料
| 型號： | PCM3060 |
| 元件分類： | Codec |
| 英文描述： | 24-BIT, 96/192-kHz ASYNCHRONOUS STEREO AUDIO CODEC |
| 中文描述： | 24位96/192-kHz異步立體聲音頻編解碼 |
| 文件頁數： | 41/45頁 |
| 文件大?。?/td> | 394K |
| 代理商： | PCM3060 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁
www.ti.com
DESIGN AND LAYOUT CONSIDERATIONS IN APPLICTION
Power Supply Pins (V
CC
, V
DD
)
The digital and analog power supply lines to the PCM3060 should be bypassed to the corresponding ground
pins with 0.1-
μ
F ceramic and 10-
μ
F electrolytic capacitors as close to the pins as possible to maximize the
dynamic performance of the ADC and DAC.
Grounding (AGND1, AGND2, SGND, DGND)
V
IN
L, V
IN
R Pins
A 4.7-
μ
F electrolytic capacitor is recommended as the ac coupling capacitor, which gives a 3-Hz cutoff
frequency. If higher full-scale input voltage is required, it can be adjusted by adding only one series resistor to
the V
IN
X pins, although a small gain error is added due to variations of absolute input resistance of the
PCM3060. For example, adding 9.1 k
gives 2 Vrms full-scale with about 10% gain error.
V
COM
Pin
Ceramic 0.1-
μ
F and electrolytic 10-
μ
F capacitors are recommended between V
COM
and AGND to ensure low
source impedance of the ADC and DAC references. These capacitors should be located as close as possible to
the V
COM
pins to reduce dynamic errors on ADC and DAC references.
V
OUT
L+, V
OUT
L–, V
OUT
R+, V
OUT
R– Pins
The differential to single-ended buffer with post LPF can be directly (without capacitor) connected to these
output pins, thereby minimizing the use of coupling capacitors for the 2-Vrms outputs. The output pins in
single-ended mode are assigned to V
OUT
L+ and V
OUT
R+ ; in single-ended mode, the V
OUT
L– and V
OUT
R– pins
must be open.
MODE Pin
System Clocks
PCM3060
SLAS533–MARCH 2007
Although the PCM3060 has two power lines to maximize the potential of dynamic performance, using one
common source, 5-V power supply for V
and a 3.3-V power supply for V
which is generated from the 5-V
power supply for V
CC
, is recommended to avoid unexpected problems, such as latch-up, from incorrect power
supply sequencing.
To maximize the dynamic performance of the PCM3060, the analog and digital grounds are not connected
internally. These points should have very low impedance to avoid digital noise and signal components feeding
back into the analog ground. So, they should be connected directly to each other under the parts to reduce the
potential of noise problems.
This pin is a logic input with quad-state input capability.
The pin is connected to V
DD
for High, to DGND for Low, and pulled up or pulled down through an external
resistor and for the two mid-states in order to distinguish the four input states. The pullup or pulldown resistor
must be 220 k
,
±
5% tolerance.
The quality of SCKI1/2 may influence dynamic performance, as the PCM3060 (both ADC and DAC) operates
based on SCKI1/2. Therefore, it may be required to consider the jitter, duty, rise and fall time, etc. of the system
clocks.
The PCM3060 supports asynchronous operation between the ADC and DAC. Therefore, there is no restriction
on the relationship between SCKI1 and SCKI2 for digital operation, but it is strongly recommended to use a
common clock if the application does not require different base clock frequencies, like 44.1 kHz and 48 kHz.
41
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| PCM3060PW | 24-BIT, 96/192-kHz ASYNCHRONOUS STEREO AUDIO CODEC |
| PCM3060PWR | 24-BIT, 96/192-kHz ASYNCHRONOUS STEREO AUDIO CODEC |
| PCM3500DATASHEET | PCM3500 Data Sheet - Low Voltage. Low Power. 16-Bit. Mono SoundPlus VOICE |
| PCM3793A | 16-Bit, Low-Power Stereo Audio CODEC With Microphone Bias, Headphone, and Digital Speaker Amplifier |
| PCM3793ARHBR | 16-Bit, Low-Power Stereo Audio CODEC With Microphone Bias, Headphone, and Digital Speaker Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCM3060PW | 功能描述:接口—CODEC 24B 96/192kHz Asynchronous Stereo RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| PCM3060PW | 制造商:Texas Instruments 功能描述:LEADED PROCESS COMPATIBLE:YES |
| PCM3060PWG4 | 功能描述:接口—CODEC 24bit 96/192kHz Asynch St Aud Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| PCM3060PWR | 功能描述:接口—CODEC 24B 96/192kHz Asynchronous Stereo RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| PCM3060PWRG4 | 功能描述:接口—CODEC 24bit 96/192kHz Asynch St Aud Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。