- 您現在的位置：買賣IC網 > PDF目錄369952 > PCM4201PWR Low Power, 24-Bit, Single Channel Audio Analog-to-Digital Converter PDF資料下載
參數資料
| 型號： | PCM4201PWR |
| 英文描述： | Low Power, 24-Bit, Single Channel Audio Analog-to-Digital Converter |
| 中文描述： | 低功耗，24位，單聲道音頻模擬數字轉換器 |
| 文件頁數： | 11/21頁 |
| 文件大?。?/td> | 248K |
| 代理商： | PCM4201PWR |
SBAS342A DECEMBER 2004 REVISED MARCH 2005
www.ti.com
11
ANALOG INPUTS
The PCM4201 features differential voltage inputs. V
IN
+
(pin 1) and V
IN
(pin 2) provide the noninverting and
inverting inputs, respectively. The full-scale input voltage,
measured differentially across these two pins, is
approximately
5.0V
PP
.
The
approximately 15k
per input pin.
input
impedance
is
In applications where the analog inputs can be driven
beyond the analog supply rails of the PCM4201, the input
buffer circuit should incorporate clamping or limiting
circuitry to ensure that the analog inputs are not driven
beyond the absolute maximum input levels for these pins.
Refer to the
Absolute Maximum Ratings
table of this
datasheet.
VOLTAGE REFERENCE
The PCM4201 includes an on-chip band gap reference for
the delta-sigma modulator, eliminating the need for
external reference circuitry. The reference voltage is set to
+2.5V nominal. The V
REF
+ (pin 16) and V
REF
(pin 15)
outputs provide connections for reference decoupling
capacitors, which are connected between these two pins.
The V
REF
output is then connected to analog ground.
Figure 2 shows the recommended decoupling capacitor
connections and values.
+
PCM4201
10
μ
F
AGND
V
REF
+
V
REF
16
15
0.1
μ
F
Figure 2. Voltage Reference Connections
The voltage reference output is not buffered, and should
not be connected to external circuitry other than the
decoupling capacitors. DC common-mode voltage for the
input buffer circuitry may be set using an external voltage
divider circuit, as shown in the
Applications Information
section of this datasheet.
SYSTEM CLOCK
The PCM4201 requires an external system clock, which is
used internally to derive the modulator oversampling and
digital subsystem clocks. The system clock is input at
SCKI (pin 12). The acceptable system clock frequency
and duty cycle range are listed in the Electrical
Characteristics table of this datasheet.
The PCM4201 supports specific system clock rates, which
are multiples of the desired output sampling frequency.
The supported system clock rate is also dependent upon
the audio serial port mode. Table 1 and Table 2 specify the
system clock rates required for common output sampling
frequencies for both Slave and Master mode audio
serial-port operation.
Table 1. System Clock Rates for Common Audio
Sampling Frequencies—Slave Mode Operation
SAMPLING
MODE
Normal
Normal
Normal
Double
Double
SAMPLING
FREQUENCY
(kHz)
32
44.1
48
88.2
96
SYSTEM CLOCK
FREQUENCY (MHZ)
SCKI = 256f
S
8.192
11.2896
12.288
22.5792
24.576
SCKI = 512f
S
16.384
22.5792
24.576
n/a
n/a
Table 2. System Clock Rates for Common Audio
Sampling Frequencies—Master Mode Operation
SAMPLING
MODE
Normal
Normal
Normal
Double
Double
SAMPLING
FREQUENCY
(kHz)
32
44.1
48
88.2
96
SYSTEM CLOCK
FREQUENCY (MHZ)
SCKI = 256f
S
N/A
N/A
N/A
22.5792
24.576
SCKI = 512f
S
16.384
22.5792
24.576
n/a
n/a
SAMPLING MODES
The PCM4201 supports three sampling modes, allowing the
user to select the most appropriate power/performance
combination for a given application. The following
paragraphs describe the operation and tradeoffs for the three
sampling modes. For all cases, f
S
is defined as the desired
output sampling rate at the audio serial port interface.
Normal Speed, Low Power mode provides the lowest
overall power dissipation, while supporting sampling rates
up to 54kHz. The modulator oversampling rate is 64f
S
for
this mode, which results in lower dynamic range and
THD+N when compared to Normal Speed, High
Performance mode. For best dynamic performance and
lowest power consumption when using Low Power mode,
it is recommended to operate the PCM4201 from a +1.8V
digital power supply.
相關PDF資料 |
PDF描述 |
|---|---|
| PCM4222_07 | High-Performance, Two-Channel, 24-Bit, 216kHz Sampling Multi-Bit Delta-Sigma Analog-to-Digital Converter |
| PCM4222PFBG4 | High-Performance, Two-Channel, 24-Bit, 216kHz Sampling Multi-Bit Delta-Sigma Analog-to-Digital Converter |
| PCM4222PFBRG4 | High-Performance, Two-Channel, 24-Bit, 216kHz Sampling Multi-Bit Delta-Sigma Analog-to-Digital Converter |
| PCM4222 | High-Performance, Two-Channel, 24-Bit, 216kHz Sampling Multi-Bit Delta-Sigma Analog-to-Digital Converter |
| PCM4222PFB | High-Performance, Two-Channel, 24-Bit, 216kHz Sampling Multi-Bit Delta-Sigma Analog-to-Digital Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCM4201PWRG4 | 功能描述:音頻模/數轉換器 IC Low Power 24-Bit Single Ch Audio A/D RoHS:否 制造商:Wolfson Microelectronics 轉換速率: 分辨率: ADC 輸入端數量: 工作電源電壓: 最大工作溫度: 最小工作溫度: 安裝風格: 封裝 / 箱體: 封裝: |
| PCM4202 | 制造商:BB 制造商全稱:BB 功能描述:High-Performance 24-Bit, 216kHz Sampling Stereo Audio Analog-to-Digital Converter |
| PCM4202DB | 功能描述:音頻模/數轉換器 IC 24-Bit/192kHz 118dB Stereo Audio A/D RoHS:否 制造商:Wolfson Microelectronics 轉換速率: 分辨率: ADC 輸入端數量: 工作電源電壓: 最大工作溫度: 最小工作溫度: 安裝風格: 封裝 / 箱體: 封裝: |
| PCM4202DBG4 | 功能描述:音頻模/數轉換器 IC 24-Bit/192kHz 118dB Stereo Audio A/D RoHS:否 制造商:Wolfson Microelectronics 轉換速率: 分辨率: ADC 輸入端數量: 工作電源電壓: 最大工作溫度: 最小工作溫度: 安裝風格: 封裝 / 箱體: 封裝: |
| PCM4202DBR | 功能描述:音頻模/數轉換器 IC 24-Bit/192kHz 118dB Stereo Audio A/D RoHS:否 制造商:Wolfson Microelectronics 轉換速率: 分辨率: ADC 輸入端數量: 工作電源電壓: 最大工作溫度: 最小工作溫度: 安裝風格: 封裝 / 箱體: 封裝: |
發布緊急采購，3分鐘左右您將得到回復。