!
US Office
70 Rio Robles
San Jose, CA 95134 USA
Tel: 408-965-2100 Fax: 408-383-0455
Taiwan Office
10F-2, 160, Sec 6, Mnchuan E. Rd.,
Taipei, Taiwan, R. O. C.
Tel: +886-2-2793-9908 Fax: +886-2-2791-6543
Japan Office
Yoshida Bldg. 501
4-1-31, Kudankita, Chiyoda-ku, Tokyo 102
Tel: +81-3-3288-2410 Fax: +81-3-3288-2375
Europe Office
26 Rue Des Sources
91530 Sermaise, France
Tel: +33-1-6459-6464 Fax: +33-1-6459-3859
Motherboard integration of the modemsubsystemhas been problematic to date, in large part due to FCC and
other international telecomcertification processes that delay the introduction of a motherboard when the
modems analog I/O (codec and DAA) circuitry was physically soldered to the board. Resolving
homologation/certification issues for OEMs is one of the key objectives of the AMR specification.
With an open, Industry-standard riser solution, a systemmanufacturer is free to implement audio and/or modem
functions on the motherboard at a lower bill of materials (BOM) cost than would be possible by deploying these
functions in either industry-standard expansion slots or in a proprietary method.
PC-TEL has streamined the traditional modeminto the Host Signal Processing (HSP) solution. Operating
with the Pentiumclass processors, HSP becomes part of the host computers systemsoftware. It requires less
power to operate and less physical space than standard modemsolutions. PC-TEL’s HSP modemis an easily
integrated, cost-effective communications solution that is flexible enough to carry you into the future.
The 2303 chip set is an integrated direct access arrangement (DAA) and Codec that provides a programmable
line interface to meet international telephone line requirements. The 2303 chip set is available in two 16-pin
small outline packages (AC’97 interface on PCT303A and phone-line interface on PCT303W). The chip set
elimnates the need for an AFE, an isolation transformer, relays, opto-isolators, and 2- to 4-wire hybrid. The
2303 chip set dramatically reduces the number of discrete components and cost required to achieve compliance
with international regulatory requirements. The PCT303A complies with AC’97 Interface specification Rev. 2.1.
The chip set is fully programmable to meet world-wide telephone line interface requirements including those
described by CTR21, NET4, JATE, FCC, and various country-specific PTT specifications. The programmable
parameters of the 2303 chip set include AC termnation, DC termnation, ringer impedance, and ringer threshold.
The 2303 chip set has been designed to meet stringent world-wide requirements for out-of-band energy, billing-
tone immunity, lightning surges, and safety requirements.
RJ11
RJ11
AMR 46-pin Connector
AC ‘97 Digital
Controller
Integrated 2303 DAA/Codec
AC ‘97 Audio Codec
AC ‘97 Digital Controller
MDC 30-pin Connector
Modem Daughter Card
Integrated DAA/Codec Chip Set
AC ‘97 Audio Codec
2303W Chip Set
MDC
I/F
30-Pin
27*45mm
MicroModem Daughter Card
(MD2)
Modem Riser Card
(MR2)
68mm
Intel AMR I/F
2303W Chip Set
6
PCT2303 for AMR & MDC
Codec/DAA Features
86dB dynamc range TX/RX
paths
2-4 –wire hybrid
Integrated ring detector
High Voltage Isolation of 2000V
4000V International
Support for “Caller ID”
Compliant with FCC Part 68,
CTR21, Net 4 and JATE
Low power standby
Low profile SOIC package
( 2 ) SOIC 16 pins 10x3x1.55mm
Low power consumption
10mA @ 3.3V operation
1mA @ 3.3V power down
Standard Features
Data
ITU-T V.90 V.34, V.32bis, V.32,
V.22bis, V.22, V.21, V.23,
Bell 212A, Bell 103
Data Compression
ITU-T V.42bis
MNP Class 5
Error Correction
ITU-T V.42 LAPM
MNP 2-4
Fax
ITU-T V. 17, V.29, V.27ter, V.21
Channel 2
Group 3
EIA Class I
Operating Systems
Windows 98, NT 4.0, Windows
CE 2.0, and Linux
PTT Approved
Countries
Australia *
Austria
Belgium
Bulgaria *
Canada
Cyprus *
Denmark
Finland
France
Germany
Greece *
Iceland *
Ireland
Israel *
Italy
Japan
Luxembourg *
Malta
Netherlands
New Zealand *
Norway
Portugal
Singapore *
South Africa *
Spain
Sweden
Switzerland
United Kingdom
USA
Approval pending in countries
marked with *