- 您現在的位置：買賣IC網 > PDF目錄367860 > PDIUSBH11A (NXP Semiconductors N.V.) Universal Serial Bus hub(通用串行總線集線器) PDF資料下載
參數資料
| 型號： | PDIUSBH11A |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Universal Serial Bus hub(通用串行總線集線器) |
| 中文描述： | 通用串行總線集線器（通用串行總線集線器） |
| 文件頁數： | 9/28頁 |
| 文件大?。?/td> | 157K |
| 代理商： | PDIUSBH11A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Philips Semiconductors
Product specification
PDIUSBH11A
Universal Serial Bus Hub
1999 Jul 22
9
APPLICATION DIAGRAM
I
2
C
GOODLINK
LED
POWER SWITCH
AND
OVERCURRENT CIRCUIT
5V
SWITCHED
5V
H11A
μ
C
CLKOUT
12MHz
USB
DOWNSTREAM
USB
UPSTREAM
3.3V
SV00840
I
2
C Interface
The I
2
C bus is used to interface to an external microcontroller
needed to control the operation of the hub. For cost consideration,
the target system microcontroller can be shared and utilized for this
purpose. The PDIUSBH11A implements a slave I
2
C interface. When
the PDIUSBH11A needs to communicate with the microcontroller it
asserts an interrupt signal. The microcontroller services this interrupt
by reading the appropriate status register on the PDIUSBH11A
through the I
2
C bus. (For more information about the I
2
C serial bus,
refer to the I
2
C Handbook Philips order number 9397 750 00013).
The I
2
C interface on the PDIUSBH11A defines two types of
transactions:
1.
command transaction
A command transaction is used to define which data (e.g., status
byte, buffer data, ...) will be read from / written to the USB
interface in the next data transaction. A data transaction usually
follows a command transaction.
2.
data transaction
A data transaction reads data from / writes data to the USB
interface. The meaning of the data is dependent on the
command transaction which was sent before the data
transaction.
Two addresses are used to differentiate between command and
data transactions. Writing to the command address is interpreted as
a command, while reading from / writing to the data address is used
to transfer data between the PDIUSBH11A and the controller.
ADDRESS TABLE
TYPE OF ADDRESS
PHYSICAL ADDRESS
(MSB to LSB)
Command
0011 011 (binary)
Data
0011 010 (binary)
Protocol
An I
2
C transaction starts with a Start Condition, followed by an
address. When the address matches either the command or data
address the transaction starts and runs until a Stop Condition or
another Start Condition (repeated start) occurs.
The command address is write-only and is unable to do a read. The
next bytes in the message are interpreted as commands. Several
command bytes can be sent after one command address. Each of
the command bytes is acknowledged and passed on to the Memory
Management Unit inside the PDIUSBH11A.
When the start condition address matches the data address, the
next bytes are interpreted as data. When the RW bit in the address
indicates a ‘master writes data to slave’ (=‘0’) the bytes are received,
acknowledged and passed on to the Memory Management Unit. If
the RW bit in the address indicates a ‘master reads data from slave’
(=‘1’) the PDIUSBH11A will send data to the master. The I
2
C-master
must acknowledge all data bytes except the last one. In this way the
I
2
C interface knows when the last byte has been transmitted and it
then releases the SDA line so that the master controller can
generate the STOP condition.
Repeated start support allows another packet to be sent without
generating a Stop Condition.
Timing
The I
2
C interface in the PDIUSBH11A can support clock speeds up
to 1MHz.
相關PDF資料 |
PDF描述 |
|---|---|
| PDIUSBH11ANB | Universal Serial Bus Hub |
| PDIUSBH11AD | Universal Serial Bus Hub |
| PDIUSBH11 | Universal Serial Bus Hub |
| PDIUSBH11D | Universal Serial Bus Hub |
| PDIUSBH11NB | Plug In Relay Switch Function:4PDT; Contact Carry Current:15A; Coil Voltage AC Max:120V; Mounting Type:Socket; Contact Carrying Power:0.9W; Contact Rating:3A; Relay Type:General Purpose RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PDIUSBH11AD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus Hub |
| PDIUSBH11AD-T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BUS CONTROLLER |
| PDIUSBH11ANB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus Hub |
| PDIUSBH11D | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus Hub |
| PDIUSBH11DB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BUS CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。