參數資料
型號： PDIUSBH11NB
廠商： NXP SEMICONDUCTORS
元件分類： 總線控制器
英文描述： Plug In Relay Switch Function:4PDT; Contact Carry Current:15A; Coil Voltage AC Max:120V; Mounting Type:Socket; Contact Carrying Power:0.9W; Contact Rating:3A; Relay Type:General Purpose RoHS Compliant: Yes
中文描述： UNIVERSAL SERIAL BUS CONTROLLER, PDIP32
封裝： 0.400 INCH, SHRINK, PLASTIC, SOT-232-1, DIP-32
文件頁數： 3/26頁
文件大?。?/td> 146K
代理商： PDIUSBH11NB
Philips Semiconductors
Product specification
PDIUSBH11
Universal Serial Bus Hub
1997 Aug 01
3
Analog Transceivers
These transceivers interface directly to the USB cables through
some termination resistors. They are capable of transmitting and
receiving serial data at both “full speed” (12 Mbit/s) and “l(fā)ow speed”
(1.5 Mbit/s) data rates.
Hub Repeater
The hub repeater is responsible for managing connectivity on a per
packet basis. It implements packet signaling connectivity and
resume connectivity.
Low speed devices can be connected to downstream ports since the
repeater will not propagate upstream packets to downstream ports,
to which low speed devices are connected, unless they are
preceded by a PREAMBLE PID.
End of Frame Timers
This block contains the specified EOF1 and EOF2 timers which are
used to detect loss-of-activity and babble error conditions in the hub
repeater. The timers also maintain the low-speed keep-alive strobe
which is sent at the beginning of a frame.
General and Individual Port Controller
The general and individual port controllers together provide status
and control of individual downstream ports. Via the I
2
C-interface a
microcontroller can access the downstream ports and request or
change the status of each individual port.
Any change in the status or settings of the individual port will result
in an interrupt request. Via an interrupt register, the servicing
microcontroller can look up the downstream port which generated
ENDPOINT DESCRIPTIONS
The following table summarizes the endpoints supported by the PDIUSBH11.
the interrupt and request its new status. Any port status change can
then be reported to the host via the hub status change (interrupt)
endpoint.
Bit Clock Recovery
The bit clock recovery circuit recovers the clock from the incoming
USB data stream using (4X) over-sampling principle. It is able to
track jitter and frequency drift specified by the USB spec.
Philips Serial Interface Engine (PSIE)
The Philips SIE implements the full USB protocol layer. It is
completely hardwired for speed and needs no firmware intervention.
The functions of this block include: synchronization pattern
recognition, parallel / serial conversion, bit stuffing / destuffing, CRC
checking / generation, PID verification / generation, address
recognition, handshake evaluation / generation.
Memory Management Unit (MMU) and Integrated RAM
The MMU and the integrated RAM is used to handle the large
difference in data-rate between USB, running in burst of 12 Mbit/s
and the I
2
C interface to the microcontroller, running at 100 kbit/s.
This allows the microcontroller to read and write USB packets at its
own (low) speed through I
2
C.
I
2
C Slave Interface
This block implements the necessary I
2
C interface protocol. A slave
I
2
C allows for simple micro-coding. An interrupt is used to alert the
microcontroller whenever the PDIUSBH11 needs attention. As a
slave I
2
C device, the PDIUSBH11 I
2
C clock: SCL is an input and is
controlled by the microcontroller.
FUNCTION
ENDPOINT
NUMBER
ENDPOINT TYPE
TRANSFER TYPE
DIRECTION
MAXIMUM PACKET SIZE
(bytes)
HUB
0
Default
Control
IN, OUT
8
1
Status change
Interrupt
IN
1
EMBEDDED
0
Default
Control
IN, OUT
8
1
Interrupt
Interrupt
IN
8
PIN DESCRIPTION
The PDIUSBH11 has two modes of operation. The first mode
(Mode 0) enables the pins DNx_EN_N to power a LED indicating
the port is enabled. The second mode (Mode 1) utilizes the LED
enable pins as per port overcurrent condition pins.
The voltage level at power up on the TEST1 and TEST2 pins
determine the PDIUSBH11 mode of operation. When both of the
pins are connected to Ground, Mode 0 is enabled. When pins
TEST1 and TEST2 are connected to Vcc, Mode 1 is enabled. Note
that in Mode 1 the pin DN2_EN_N remains an LED enable pin. Pin
TEST3 should always be connected to Ground at all times.
相關PDF資料
PDF描述
PDIUSBH12 USB 2-port hub
PDIUSBH12D USB 2-port hub
PDIUSBH12N USB 2-port hub
PDIUSBP11A Universal Serial Bus Transceiver(通用串行總線收發器)
PDUSBP11APWDH Universal Serial Bus Transceiver
相關代理商/技術參數
參數描述
PDIUSBH12 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB 2-port hub
PDIUSBH12D 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB 2-port hub
PDIUSBH12N 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:USB 2-port hub
PDIUSBH12NB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BUS CONTROLLER
PDIUSBP11 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus transceiver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*