![](http://datasheet.mmic.net.cn/260000/PI2BV3877_datasheet_15938840/PI2BV3877_2.png)
2
PS8472A 05/02/00
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
PI2BV3877
2.5V, 10-Bit, 2-Port
266 MHz DDR BusSwitch
DC Electrical Characteristics
(Over the Operating Range, T
A
= 0°C to +85°C, V
CC
= 2.3V to 2.7V)
Parameters Description
Test Conditions
(1)
Min.
Typ.
(2)
Max.
Units
V
IH
Input HIGH Voltage (BE0, BE1)
Guaranteed Logic HIGH Level
1.6
V
CC
+ 0.3
0.9
V
IL
Input LOW Voltage (BE0, BE1)
Guaranteed Logic LOW Level
0.3
I
OZH
High Impedance Output Current B @ 2.5V
250
μA
V
IK
Clamp Diode Voltage
Switch On Resistance
(4)
V
CC
= Min., I
IN
= 18mA
1.2
V
R
ON
V
CC
= Min., V
IN
= 0.9V, I
ON
= 20mA
17
33
V
CC
= Min., V
IN
= 1.6V, I
ON
= 15mA
22
30
R
PU
Pull-up Resistance
115
150
200
Storage Temperature...............................................................65°C to +150°C
Ambient Temperature with Power Applied.............................. 40°C to +85°C
Supply Voltage to Ground Potential (Inputs & V
CC
Only) ........0.5V to +4.6V
Supply Voltage to Ground Potential (Outputs & D/O Only)......0.5V to +4.6V
DC Input Voltage .......................................................................0.5V to +4.6V
DC Output Current.................................................................................120mA
Power Dissipation .................................................................................... 0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device.
This is a stress rating only and functional operation of the
device at these or any other conditions above those indi-
cated in the operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions
for extended periods may affect reliability.
Capacitance
(T
A
= 25°C, f = 1 MHz)
Parameters
(4)
Description
Test Conditions
Typ.
Units
C
IN
C
OFF
C
ON
(A/B)
Input Capacitance
A Capacitance, Switch Off
A/B Capacitance, Switch On
V
IN
= 0V
V
IN
= 0V
V
IN
= 0V
3
3
7
pF
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V
CC
= 2.5V, T
A
= 25°C ambient and maximum loading.
3. Measured by the voltage drop between A and B pin at indicated current through the switch.
ON resistance is determined by the lower of the voltages on the two (A,B) pins.
4. This parameter is determined by device characterization but is not production tested.
V
Power Supply Characteristics
Parameters Description
Test Conditions
(1)
Min.
Typ.
(2)
Max.
Units
I
CC
Quiescent Power
Supply Current
V
CC
= Max.
V
IN
= V
CC
V
IN
= GND
–
–
10
56
μ
A
mA
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device.
2. Typical values are at V
CC
= 2.5V, +25°C ambient.
3. Per TTL driven input (control input only); A and B pins do not contribute to I
CC
.