![](http://datasheet.mmic.net.cn/260000/PI3C3245_datasheet_15938999/PI3C3245_2.png)
2
PS8162B 12/10/99
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
PI3C3245
2.5V/3.3V, High Bandwidth,
Hot Insertion, 8-Bit, 2-Port, Bus Switch
Storage Temperature ........................................................65°C to +150°C
Ambient Temperature with Power Applied ......................... 40°C to +85°C
Supply Voltage to Ground Potential (Inputs & V
CC
Only) ........0.5V to +4.6V
Supply Voltage to Ground Potential (Outputs & D/O Only) ......0.5V to +4.6V
DC Input Voltage .................................................................. 0.5V to +5.5V
DC Output Current ............................................................................120mA
Power Dissipation................................................................................ 0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the de-
vice. This is a stress rating only and functional opera-
tion of the device at these or any other conditions above
those indicated in the operational sections of this
specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may
affect reliability.
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
DC Electrical Characteristics
(Over Operating Range, T
A
= –40°C to +85°C, V
CC
= 3.3V ±10%)
Test Conditions
(1)
V
IH
Input HIGH Voltage
Guaranteed Logic HIGH Level
V
IL
Input LOW Voltage
Guaranteed Logic LOW Level
I
IH
Input HIGH Current
V
CC
= Max., V
IN
= V
CC
I
IL
Input LOW Current
V
CC
= Max., V
IN
= GND
I
OZH
High Impedance Output Current
0
≤
A, B
≤
V
CC
V
IK
Clamp Diode Voltage
V
CC
= Min., I
IN
= –18mA
R
ON
Switch On Resistance
(4)
V
CC
= Min., V
IN
= 0.0V, I
ON
= 48mA
V
CC
= Min., V
IN
= 2.4V, I
ON
= 15mA
Parameters Description
Min.
2.0
Typ.
(2)
Max.
Units
–0.5
0.8
±1
±1
μA
±1
–0.73
–1.2
V
5
8
7
15
Parameters
(5)
C
IN
C
OFF
C
ON
Description
Test Conditions
Typ.
Units
Input Capacitance
A/B Capacitance, Switch Off
A/B Capacitance, Switch On
V
IN
= 0V
V
IN
= 0V
V
IN
= 0V
3.5
5.0
10.0
pF
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V
CC
= 3.3V, T
A
= 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined
by the lower of the voltages on the two (A,B) pins.
5. This parameter is determined by device characterization but is not production tested.
V
Capacitance
(T
A
= 25°C, f = 1 MHz)