![](http://datasheet.mmic.net.cn/260000/PI3CH1000L_datasheet_15939018/PI3CH1000L_2.png)
2
PS2724B 05/09/06
PI3CH1000
Low Voltage, 5-Ohm, 10-Channel
2-Port
NanoSwitch
Storage Temperature................................................–65°C to +150°C
Ambient Temperature with Power Applied ...............–40°C to +85°C
Supply Voltage to Ground Potential ...........................–0.5V to +4.6V
DC Input Voltage ........................................................–0.5V to +6.0V
DC Output Current................................................................... 120mA
Power Dissipation....................................................................... 0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these
or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect re-
liability.
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
DC Electrical Characteristics, 3.3V Supply
(Over Operating Range, T
A
= –40°C to +85°C, V
CC
= 3.3V ± 10%)
Parameters
Description
V
IH
Input HIGH Voltage
Guaranteed Logic HIGH Level
V
IL
Input LOW Voltage
Guaranteed Logic LOW Level
V
IK
Clamp diode Voltage
V
CC
= Min., I
IN
= –18mA
I
IH
Input HIGH Current
V
CC
= Max., V
IN
= V
CC
I
IL
Input LOW Current
V
CC
= Max., V
IN
= GND
I
OZH
High-Impedence Current
0 ≤ A, B ≤ V
CC
V
CC
= Min.,V
IN
= 0V,
I
ON
= –48mA or –64mA
V
CC
= Min., V
IN
= 3.6V, I
ON
= –15mA
Test Conditions
(1)
Min.
2
–0.5
Typ.
(2)
Max.
Units
V
0.8
–1.8
±1
±1
±1
–1.3
μA
R
ON
Switch On-Resistance
(3)
4
6
5
8
DC Electrical Characteristics, 2.5V Supply
(Over Operating Range, T
A
= –40°C to +85°C, V
CC
= 2.5V ± 10%)
Parameters
Description
V
IH
Input HIGH Voltage
Guaranteed Logic HIGH Level
V
IL
Inout LOW Voltage
Guaranteed Logic LOW Level
V
IK
Clamp Diode Voltage
V
CC
= Max., I
IN
= –6mA
I
IH
Input HIGH Current
V
CC
= Max., V
IN
= V
CC
I
IL
Input LOW Current
V
CC
= Max., V
IN
= GND
I
OZH
High Impedance Current
0 ≤ A, B ≤ V
CC
V
CC
= Min., V
IN
= 0V,
I
ON
= –48mA
V
CC
= Min., V
IN
= 2.25V,
I
ON
= –15mA
Test Conditions
(1)
Min.
1.8
–0.3
Typ.
(2)
Max.
V
CC
+ 0.3
0.8
–1.8
±1
±1
±1
Units
V
–0.7
μA
R
ON
Switch On-Resistance
(3)
4
8
7
14
Notes:
1.
2.
3.
For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
Typical values are at V
CC
= 3.3V, T
A
= 25°C ambient and maximum loading.
Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined
by the lower of the voltages on the two (A,B) pins.
Notes:
1.
2.
3.
For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
Typical values are at V
CC
= 3.3V, T
A
= 25°C ambient and maximum loading.
Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined
by the lower of the voltages on the two (A,B) pins.
06-0235