- 您現在的位置：買賣IC網 > PDF目錄11570 > PIC12F629-I/MD (Microchip Technology)IC PIC MCU FLASH 1KX14 8DFN PDF資料下載
參數資料
| 型號： | PIC12F629-I/MD |
| 廠商： | Microchip Technology |
| 文件頁數： | 9/35頁 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 1KX14 8DFN |
| 產品培訓模塊： | Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio |
| 標準包裝： | 91 |
| 系列： | PIC® 12F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 20MHz |
| 外圍設備： | POR，WDT |
| 輸入/輸出數： | 5 |
| 程序存儲器容量： | 1.75KB（1K x 14） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大小： | 128 x 8 |
| RAM 容量： | 64 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2 V ~ 5.5 V |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 8-VDFN 裸露焊盤 |
| 包裝： | 管件 |
| 產品目錄頁面： | 637 (CN2011-ZH PDF) |
| 配用： | AC164326-ND - MODULA SKT PM3 20QFN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
17
AT89S53
0787E–MICRO–3/06
Timer 2 interrupt is generated by the logical OR of bits TF2
and EXF2 in register T2CON. Neither of these flags is
cleared by hardware when the service routine is vectored
to. In fact, the service routine may have to determine
whether it was TF2 or EXF2 that generated the interrupt,
and that bit will have to be cleared in software.
The Timer 0 and Timer 1 flags, TF0 and TF1, are set at
S5P2 of the cycle in which the timers overflow. The values
are then polled by the circuitry in the next cycle. However,
the Timer 2 flag, TF2, is set at S2P2 and is polled in the
same cycle in which the timer overflows.
Oscillator Characteristics
XTAL1 and XTAL2 are the input and output, respectively,
of an inverting amplifier that can be configured for use as
an on-chip oscillator, as shown in Figure 11. Either a quartz
crystal or ceramic resonator may be used. To drive the
device from an external clock source, XTAL2 should be left
unconnected while XTAL1 is driven, as shown in Figure 12.
There are no requirements on the duty cycle of the external
clock signal, since the input to the internal clocking circuitry
is through a divide-by-two flip-flop, but minimum and maxi-
mum voltage high and low time specifications must be
observed.
Figure 11. Oscillator Connections
Note:
C1, C2 = 30 pF
± 10 pF for Crystals
= 40 pF
± 10 pF for Ceramic Resonators
Figure 12. External Clock Drive Configuration
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16F689-E/SO | IC PIC MCU FLASH 4KX14 20SOIC |
| V300C48M75BF | CONVERTER MOD DC/DC 48V 75W |
| PIC16F685-E/SO | IC PIC MCU FLASH 4KX14 20SOIC |
| V300C48M75BL3 | CONVERTER MOD DC/DC 48V 75W |
| VI-22X-IX-S | CONVERTER MOD DC/DC 5.2V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC12F629IMF | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin FLASH-Based 8-Bit CMOS Microcontrollers |
| PIC12F629-IMF | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, Flash-Based 8-Bit CMOS Microcontrollers |
| PIC12F629IP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin FLASH-Based 8-Bit CMOS Microcontrollers |
| PIC12F629-IP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, Flash-Based 8-Bit CMOS Microcontrollers |
| PIC12F629ISN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin FLASH-Based 8-Bit CMOS Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。