參數資料
型號： PIC16CR76-I/SO
廠商： Microchip Technology
文件頁數： 110/172頁
文件大?。?/td> 0K
描述： IC PIC MCU 8KX14 28SOIC
標準包裝： 27
系列： PIC® 16C
核心處理器： PIC
芯體尺寸： 8-位
速度： 20MHz
連通性： I²C，SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 22
程序存儲器容量： 14KB（8K x 14）
程序存儲器類型： ROM
RAM 容量： 368 x 8
電壓 - 電源 (Vcc/Vdd)： 2 V ~ 5.5 V
數據轉換器： A/D 5x8b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 28-SOIC（0.295"，7.50mm 寬）
包裝： 管件
PIC16CR7X
DS21993C-page 40
2007 Microchip Technology Inc.
4.6
Parallel Slave Port
The Parallel Slave Port (PSP) is not implemented on
the PIC16CR73 or PIC16CR76.
PORTD operates as an 8-bit wide Parallel Slave Port,
or microprocessor port, when control bit PSPMODE
(TRISE<4>) is set. In Slave mode, it is asynchronously
readable and writable by an external system using the
read control input pin RE0/RD, the write control input
pin RE1/WR, and the Chip Select control input pin RE2/
CS.
The PSP can directly interface to an 8-bit micro-
processor data bus. The external microprocessor can
read or write the PORTD latch as an 8-bit latch. Setting
bit PSPMODE enables port pin RE0/RD to be the RD
input, RE1/WR to be the WR input and RE2/CS to be
the CS (Chip Select) input. For this functionality, the
corresponding data direction bits of the TRISE register
(TRISE<2:0>) must be configured as inputs (i.e., set).
The A/D port Configuration bits PCFG3:PCFG0
(ADCON1<3:0>) must be set to configure pins
RE2:RE0 as digital I/O.
There are actually two 8-bit latches, one for data output
(external reads) and one for data input (external
writes). The firmware writes 8-bit data to the PORTD
output data latch and reads data from the PORTD input
data latch (note that they have the same address). In
this mode, the TRISD register is ignored, since the
external device is controlling the direction of data flow.
An external write to the PSP occurs when the CS and
WR lines are both detected low. Firmware can read the
actual data on the PORTD pins during this time. When
either the CS or WR lines become high (level trig-
gered), the data on the PORTD pins is latched, and the
Input Buffer Full (IBF) status flag bit (TRISE<7>) and
interrupt flag bit PSPIF (PIR1<7>) are set on the Q4
clock cycle, following the next Q2 cycle to signal the
write is complete (Figure 4-9). Firmware clears the IBF
flag by reading the latched PORTD data and clears the
PSPIF bit.
The Input Buffer Overflow (IBOV) status flag bit
(TRISE<5>) is set if an external write to the PSP occurs
while the IBF flag is set from a previous external write.
The previous PORTD data is overwritten with the new
data. IBOV is cleared by reading PORTD and clearing
IBOV.
A read from the PSP occurs when both the CS and RD
lines are detected low. The data in the PORTD output
latch is output to the PORTD pins. The Output Buffer
Full (OBF) status flag bit (TRISE<6>) is cleared imme-
diately (Figure 4-10), indicating that the PORTD latch is
being read, or has been read by the external bus. If
firmware writes new data to the output latch during this
time, it is immediately output to the PORTD pins, but
OBF will remain cleared.
When either the CS or RD pins are detected high, the
PORTD outputs are disabled, and the interrupt flag bit
PSPIF is set on the Q4 clock cycle following the next
Q2 cycle, indicating that the read is complete. OBF
remains low until firmware writes new data to PORTD.
When not in PSP mode, the IBF and OBF bits are held
clear. Flag bit IBOV remains unchanged. The PSPIF bit
must be cleared by the user in firmware; the interrupt
can be disabled by clearing the interrupt enable bit
PSPIE (PIE1<7>).
FIGURE 4-8:
PORTD AND PORTE
BLOCK DIAGRAM
(PARALLEL SLAVE PORT)
Data Bus
WR
Port
RD
RDx
Q
D
CK
EN
QD
EN
Port
pin
One bit of PORTD
Set Interrupt Flag
PSPIF (PIR1<7>)
Read
Chip Select
Write
RD
CS
WR
Note: I/O pin has protection diodes to VDD and VSS.
TTL
相關PDF資料
PDF描述
PIC16CR76-I/ML IC PIC MCU 8KX14 28QFN
PIC16CR74T-I/ML IC PIC MCU 4KX14 44QFN
PIC16CR74-I/PT IC PIC MCU 4KX14 44TQFP
PIC16CR74-I/P IC PIC MCU 4KX14 40DIP
PIC16CR74-I/ML IC PIC MCU 4KX14 44QFN
相關代理商/技術參數
參數描述
PIC16CR76T-I/ML 功能描述:IC PIC MCU 8KX14 28QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
PIC16CR76T-I/SO 功能描述:IC PIC MCU 8KX14 28SOIC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C，SPI，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:14 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
PIC16CR76T-I/SS 功能描述:IC PIC MCU 8KX14 28SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio 標準包裝:42 系列:PIC® 16C 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:- 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:13 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 5.5 V 數據轉換器:A/D 4x8b 振蕩器型:外部 工作溫度:-40°C ~ 85°C 封裝/外殼:18-SOIC（0.295"，7.50mm 寬） 包裝:管件 配用:XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MILISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING309-1011-ND - ADAPTER 18-SOIC TO 18-DIP309-1010-ND - ADAPTER 18-SOIC TO 18-DIPAC164010-ND - MODULE SKT PROMATEII DIP/SOIC
PIC16CR77-I/ML 功能描述:IC PIC MCU 8KX14 44QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio 標準包裝:42 系列:PIC® 16C 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:- 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:13 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 5.5 V 數據轉換器:A/D 4x8b 振蕩器型:外部 工作溫度:-40°C ~ 85°C 封裝/外殼:18-SOIC（0.295"，7.50mm 寬） 包裝:管件 配用:XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MILISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING309-1011-ND - ADAPTER 18-SOIC TO 18-DIP309-1010-ND - ADAPTER 18-SOIC TO 18-DIPAC164010-ND - MODULE SKT PROMATEII DIP/SOIC
PIC16CR77-I/P 功能描述:IC PIC MCU 8KX14 40DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio 標準包裝:42 系列:PIC® 16C 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:- 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:13 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 5.5 V 數據轉換器:A/D 4x8b 振蕩器型:外部 工作溫度:-40°C ~ 85°C 封裝/外殼:18-SOIC（0.295"，7.50mm 寬） 包裝:管件 配用:XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MILISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING309-1011-ND - ADAPTER 18-SOIC TO 18-DIP309-1010-ND - ADAPTER 18-SOIC TO 18-DIPAC164010-ND - MODULE SKT PROMATEII DIP/SOIC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*