參數資料
型號： PIC16CR76T-I/SO
廠商： Microchip Technology
文件頁數： 59/172頁
文件大?。?/td> 0K
描述： IC PIC MCU 8KX14 28SOIC
標準包裝： 1,600
系列： PIC® 16C
核心處理器： PIC
芯體尺寸： 8-位
速度： 20MHz
連通性： I²C，SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 22
程序存儲器容量： 14KB（8K x 14）
程序存儲器類型： ROM
RAM 容量： 368 x 8
電壓 - 電源 (Vcc/Vdd)： 2 V ~ 5.5 V
數據轉換器： A/D 5x8b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 28-SOIC（0.295"，7.50mm 寬）
包裝： 帶卷 (TR)
2007 Microchip Technology Inc.
DS39599G-page 149
PIC18F2220/2320/4220/4320
16.4.4
PROGRAMMABLE DEAD-BAND
DELAY
In half-bridge applications, where all power switches
are modulated at the PWM frequency at all times, the
power switches normally require more time to turn off
than to turn on. If both the upper and lower power
switches are switched at the same time (one turned on
and the other turned off), both switches may be on for
a short period of time until one switch completely turns
off. During this brief interval, a very high current (shoot-
through current) may flow through both power
switches, shorting the bridge supply. To avoid this
potentially destructive shoot-through current from flow-
ing during switching, turning on either of the power
switches is normally delayed to allow the other switch
to completely turn off.
In the Half-Bridge Output mode, a digitally program-
mable dead band delay is available to avoid shoot-
through current from destroying the bridge power
switches. The delay occurs at the signal transition from
the non-active state to the active state. See Figure 16-4
for illustration. The lower seven bits of the PWM1CON
register (Register 16-2) set the delay period in terms of
microcontroller instruction cycles (TCY or 4 TOSC).
16.4.5
ENHANCED PWM
AUTO-SHUTDOWN
When the ECCP is programmed for any of the
enhanced PWM modes, the active output pins may be
configured for auto-shutdown. Auto-shutdown immedi-
ately places the enhanced PWM output pins into a
defined shutdown state when a shutdown event
occurs.
A shutdown event can be caused by either of the two
comparator modules or the INT0 pin (or any combina-
tion of these three sources). The comparators may be
used to monitor a voltage input proportional to a current
being monitored in the bridge circuit. If the voltage
exceeds a threshold, the comparator switches state
and triggers a shutdown. Alternatively, a digital signal
on the INT0 pin can also trigger a shutdown. The auto-
shutdown feature can be disabled by not selecting any
auto-shutdown sources. The auto-shutdown sources to
be used are selected using the ECCPAS2:ECCPAS0
bits (ECCPAS<6:4>).
When a shutdown occurs, the output pins are asyn-
chronously placed in their shutdown states, specified
by the PSSAC1:PSSAC0 and PSSBD1:PSSBD0 bits
(ECCPAS<3:0>). Each pin pair (P1A/P1C and P1B/
P1D) may be set to drive high, drive low or be tri-stated
(not driving). The ECCPASE bit (ECCPAS<7>) is also
set to hold the enhanced PWM outputs in their
shutdown states.
The ECCPASE bit is set by hardware when a shutdown
event occurs. If automatic restarts are not enabled, the
ECCPASE bit is cleared by firmware when the cause of
the shutdown clears. If automatic restarts are enabled,
the ECCPASE bit is automatically cleared when the
cause of the auto-shutdown has cleared.
If the ECCPASE bit is set when a PWM period begins,
the PWM outputs remain in their shutdown state for that
entire PWM period. When the ECCPASE bit is cleared,
the PWM outputs will return to normal operation at the
beginning of the next PWM period.
Note:
Writing to the ECCPASE bit is disabled
while a shutdown condition is active.
REGISTER 16-2:
PWM1CON: PWM CONFIGURATION REGISTER
R/W-0
PRSEN
PDC6
PDC5
PDC4
PDC3
PDC2
PDC1
PDC0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
PRSEN: PWM Restart Enable bit
1 = Upon auto-shutdown, the ECCPASE bit clears automatically once the shutdown event goes away;
the PWM restarts automatically
0 = Upon auto-shutdown, ECCPASE must be cleared in software to restart the PWM
bit 6-0
PDC6:PDC0: PWM Delay Count bits
Delay time, in number of FOSC/4 (4 * TOSC) cycles, between the scheduled time when a PWM signal
should transition to active and the actual time it transitions active.
相關PDF資料
PDF描述
PIC18LF24K22-I/MV IC PIC MCU 16KB FLASH 28UQFN
PIC18LF24K22-I/ML IC PIC MCU 16KB FLASH 28QFN
PIC16CR76T-I/ML IC PIC MCU 8KX14 28QFN
PIC16F627-04/P IC MCU FLASH 1KX14 COMP 18DIP
PIC18F45J10-I/ML IC PIC MCU FLASH 16KX16 44QFN
相關代理商/技術參數
參數描述
PIC16CR77-I/ML 功能描述:IC PIC MCU 8KX14 44QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio 標準包裝:42 系列:PIC® 16C 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:- 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:13 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 5.5 V 數據轉換器:A/D 4x8b 振蕩器型:外部 工作溫度:-40°C ~ 85°C 封裝/外殼:18-SOIC（0.295"，7.50mm 寬） 包裝:管件 配用:XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MILISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING309-1011-ND - ADAPTER 18-SOIC TO 18-DIP309-1010-ND - ADAPTER 18-SOIC TO 18-DIPAC164010-ND - MODULE SKT PROMATEII DIP/SOIC
PIC16CR77-I/P 功能描述:IC PIC MCU 8KX14 40DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio 標準包裝:42 系列:PIC® 16C 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:- 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:13 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 5.5 V 數據轉換器:A/D 4x8b 振蕩器型:外部 工作溫度:-40°C ~ 85°C 封裝/外殼:18-SOIC（0.295"，7.50mm 寬） 包裝:管件 配用:XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MILISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING309-1011-ND - ADAPTER 18-SOIC TO 18-DIP309-1010-ND - ADAPTER 18-SOIC TO 18-DIPAC164010-ND - MODULE SKT PROMATEII DIP/SOIC
PIC16CR77-I/PT 功能描述:IC PIC MCU 8KX14 44TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio 標準包裝:42 系列:PIC® 16C 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:- 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:13 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 5.5 V 數據轉換器:A/D 4x8b 振蕩器型:外部 工作溫度:-40°C ~ 85°C 封裝/外殼:18-SOIC（0.295"，7.50mm 寬） 包裝:管件 配用:XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MILISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING309-1011-ND - ADAPTER 18-SOIC TO 18-DIP309-1010-ND - ADAPTER 18-SOIC TO 18-DIPAC164010-ND - MODULE SKT PROMATEII DIP/SOIC
PIC16CR77T-I/ML 功能描述:IC PIC MCU 8KX14 44QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio 標準包裝:42 系列:PIC® 16C 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:- 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:13 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 5.5 V 數據轉換器:A/D 4x8b 振蕩器型:外部 工作溫度:-40°C ~ 85°C 封裝/外殼:18-SOIC（0.295"，7.50mm 寬） 包裝:管件 配用:XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MILISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING309-1011-ND - ADAPTER 18-SOIC TO 18-DIP309-1010-ND - ADAPTER 18-SOIC TO 18-DIPAC164010-ND - MODULE SKT PROMATEII DIP/SOIC
PIC16CR77T-I/PT 功能描述:IC PIC MCU 8KX14 44TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio 標準包裝:42 系列:PIC® 16C 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:- 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:13 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 5.5 V 數據轉換器:A/D 4x8b 振蕩器型:外部 工作溫度:-40°C ~ 85°C 封裝/外殼:18-SOIC（0.295"，7.50mm 寬） 包裝:管件 配用:XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MILISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING309-1011-ND - ADAPTER 18-SOIC TO 18-DIP309-1010-ND - ADAPTER 18-SOIC TO 18-DIPAC164010-ND - MODULE SKT PROMATEII DIP/SOIC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*