參數資料
型號： PIC16CR77
廠商： Microchip Technology Inc.
英文描述： 28/40-Pin, 8-Bit CMOS ROM Microcontrollers
中文描述： 28/40-Pin，8位微控制器的CMOS光盤
文件頁數： 82/172頁
文件大?。?/td> 1506K
代理商： PIC16CR77
PIC16CR7X
DS21993C-page 80
2007 Microchip Technology Inc.
10.3.2
USART SYNCHRONOUS MASTER
RECEPTION
Once Synchronous mode is selected, reception is
enabled
by
setting
either
(RCSTA<5>), or enable bit CREN (RCSTA<4>). Data is
sampled on the RC7/RX/DT pin on the falling edge of
the clock. If enable bit SREN is set, then only a single
word is received. If enable bit CREN is set, the recep-
tion is continuous until CREN is cleared. If both bits are
set, CREN takes precedence. After clocking the last bit,
the received data in the Receive Shift Register (RSR)
is transferred to the RCREG register (if it is empty).
When the transfer is complete, interrupt flag bit RCIF
(PIR1<5>) is set. The actual interrupt can be enabled/
disabled
by
setting/clearing
(PIE1<5>). Flag bit RCIF is a read-only bit, which is
reset by the hardware. In this case, it is reset when the
RCREG register has been read and is empty. The
RCREG is a double buffered register (i.e., it is a two-
deep FIFO). It is possible for two bytes of data to be
received and transferred to the RCREG FIFO and a
third byte to begin shifting into the RSR register. On the
clocking of the last bit of the third byte, if the RCREG
register is still full, then overrun error bit OERR
(RCSTA<1>) is set. The word in the RSR will be lost.
The RCREG register can be read twice to retrieve the
two bytes in the FIFO. Bit OERR has to be cleared in
software (by clearing bit CREN). If bit OERR is set,
transfers from the RSR to the RCREG are inhibited, so
it is essential to clear bit OERR if it is set. The ninth
receive bit is buffered the same way as the receive
enable
bit
SREN
enable
bit
RCIE
data. Reading the RCREG register will load bit RX9D
with a new value, therefore, it is essential for the user
to read the RCSTA register before reading RCREG, in
order not to lose the old RX9D information.
Steps to follow when setting up a Synchronous Master
Reception:
1.
Initialize the SPBRG register for the appropriate
baud rate (
Section 10.1 “USART Baud Rate
Generator (BRG)”
).
2.
Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC.
3.
Ensure bits CREN and SREN are clear.
4.
If interrupts are desired, then set enable bit
RCIE.
5.
If 9-bit reception is desired, then set bit RX9.
6.
If a single reception is required, set bit SREN.
For continuous reception set bit CREN.
7.
Interrupt flag bit RCIF will be set when reception
is complete and an interrupt will be generated if
enable bit RCIE was set.
8.
Read the RCSTA register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
9.
Read the 8-bit received data by reading the
RCREG register.
10. If any error occurred, clear the error by clearing
bit CREN.
11. If using interrupts, ensure that GIE and PEIE in
the INTCON register are set.
FIGURE 10-8:
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
CREN bit
RC7/RX/DT pin
RC6/TX/CK pin
Write to
bit SREN
SREN bit
RCIF bit
(Interrupt)
Read
RXREG
Note:
Timing diagram demonstrates Sync Master mode with bit SREN =
1
and bit BRG =
0.
Q3Q4Q1Q2Q3Q4Q1Q2Q3Q4
Q2
Q1Q2Q3Q4Q1Q2Q3Q4 Q1Q2Q3Q4Q1Q2Q3Q4 Q1Q2Q3Q4Q1Q2Q3Q4 Q1Q2Q3Q4
‘
0
’
bit 0
bit 1
bit 2
bit 3
bit 4
bit 5
bit 6
bit 7
‘
0
’
Q1Q2Q3Q4
相關PDF資料
PDF描述
PIC16CR7X 28/40-Pin, 8-Bit CMOS ROM Microcontrollers
PIC16F628A 18-pin Flash-Based 8-Bit CMOS Microcontrollers with nanoWatt Technology(18引腳，基于FLASH的8位CMOS微控制器，使用毫微瓦特技術)
PIC16F687 20-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology
PIC16F685 20-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology
PIC16F689 20-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology
相關代理商/技術參數
參數描述
PIC16CR77-I/ML 功能描述:IC PIC MCU 8KX14 44QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio 標準包裝:42 系列:PIC® 16C 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:- 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:13 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 5.5 V 數據轉換器:A/D 4x8b 振蕩器型:外部 工作溫度:-40°C ~ 85°C 封裝/外殼:18-SOIC（0.295"，7.50mm 寬） 包裝:管件 配用:XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MILISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING309-1011-ND - ADAPTER 18-SOIC TO 18-DIP309-1010-ND - ADAPTER 18-SOIC TO 18-DIPAC164010-ND - MODULE SKT PROMATEII DIP/SOIC
PIC16CR77-I/P 功能描述:IC PIC MCU 8KX14 40DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio 標準包裝:42 系列:PIC® 16C 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:- 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:13 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 5.5 V 數據轉換器:A/D 4x8b 振蕩器型:外部 工作溫度:-40°C ~ 85°C 封裝/外殼:18-SOIC（0.295"，7.50mm 寬） 包裝:管件 配用:XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MILISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING309-1011-ND - ADAPTER 18-SOIC TO 18-DIP309-1010-ND - ADAPTER 18-SOIC TO 18-DIPAC164010-ND - MODULE SKT PROMATEII DIP/SOIC
PIC16CR77-I/PT 功能描述:IC PIC MCU 8KX14 44TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio 標準包裝:42 系列:PIC® 16C 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:- 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:13 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 5.5 V 數據轉換器:A/D 4x8b 振蕩器型:外部 工作溫度:-40°C ~ 85°C 封裝/外殼:18-SOIC（0.295"，7.50mm 寬） 包裝:管件 配用:XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MILISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING309-1011-ND - ADAPTER 18-SOIC TO 18-DIP309-1010-ND - ADAPTER 18-SOIC TO 18-DIPAC164010-ND - MODULE SKT PROMATEII DIP/SOIC
PIC16CR77T-I/ML 功能描述:IC PIC MCU 8KX14 44QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio 標準包裝:42 系列:PIC® 16C 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:- 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:13 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 5.5 V 數據轉換器:A/D 4x8b 振蕩器型:外部 工作溫度:-40°C ~ 85°C 封裝/外殼:18-SOIC（0.295"，7.50mm 寬） 包裝:管件 配用:XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MILISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING309-1011-ND - ADAPTER 18-SOIC TO 18-DIP309-1010-ND - ADAPTER 18-SOIC TO 18-DIPAC164010-ND - MODULE SKT PROMATEII DIP/SOIC
PIC16CR77T-I/PT 功能描述:IC PIC MCU 8KX14 44TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:PIC® 16C 產品培訓模塊:Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio 標準包裝:42 系列:PIC® 16C 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:- 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:13 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 5.5 V 數據轉換器:A/D 4x8b 振蕩器型:外部 工作溫度:-40°C ~ 85°C 封裝/外殼:18-SOIC（0.295"，7.50mm 寬） 包裝:管件 配用:XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MILISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING309-1011-ND - ADAPTER 18-SOIC TO 18-DIP309-1010-ND - ADAPTER 18-SOIC TO 18-DIPAC164010-ND - MODULE SKT PROMATEII DIP/SOIC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*