參數資料
型號： PIC16F83
廠商： Microchip Technology Inc.
英文描述： 8-Bit CMOS Flash/EEPROM Microcontollrs(每個I/O口有20mA吸收,25mA驅動，64字節數據EEPROM，2.0V的微控制器)
中文描述： 8位CMOS閃存/ EEPROM Microcontollrs（每個的I / O口有20mA的吸收，25mA電流驅動，64字節數據的EEPROM，2.0伏的微控制器）
文件頁數： 25/120頁
文件大小： 764K
代理商： PIC16F83
1996 Microchip Technology Inc.
DS30430A-page 25
PIC16F8X
5.3
I/O Programming Considerations
5.3.1
BI-DIRECTIONAL I/O PORTS
Any instruction which writes, operates internally as a
read followed by a write operation. The
instructions, for example, read the register into the
CPU, execute the bit operation and write the result
back to the register. Caution must be used when these
instructions are applied to a port with both inputs and
outputs defined. For example, a
of PORTB will cause all eight bits of PORTB to be read
into the CPU. Then the
BSF
bit5 and PORTB is written to the output latches. If
another bit of PORTB is used as a bi-directional I/O pin
(i.e., bit0) and it is defined as an input at this time, the
input signal present on the pin itself would be read into
the CPU and rewritten to the data latch of this particular
pin, overwriting the previous content. As long as the pin
stays in the input mode, no problem occurs. However,
if bit0 is switched into output mode later on, the content
of the data latch is unknown.
Reading the port register, reads the values of the port
pins. Writing to the port register writes the value to the
port latch. When using read-modify-write instructions
(i.e.,
BCF, BSF
, etc.) on a port, the value of the port
pins is read, the desired operation is done to this value,
and this value is then written to the port latch.
A pin actively outputting a Low or High should not be
driven from external devices at the same time in order
to change the level on this pin (“wired-or”, “wired-and”).
The resulting high output current may damage the chip.
BCF
and
BSF
BSF
operation on bit5
operation takes place on
5.3.2
SUCCESSIVE OPERATIONS ON I/O PORTS
The actual write to an I/O port happens at the end of an
instruction cycle, whereas for reading, the data must be
valid at the beginning of the instruction cycle
(Figure 5-5). Therefore, care must be exercised if a
write followed by a read operation is carried out on the
same I/O port. The sequence of instructions should be
such that the pin voltage stabilizes (load dependent)
before the next instruction which causes that file to be
read into the CPU is executed. Otherwise, the previous
state of that pin may be read into the CPU rather than
the new state. When in doubt, it is better to separate
these instructions with a
NOP
accessing this I/O port.
Example 5-3 shows the effect of two sequential
read-modify-write instructions (e.g.,
an I/O port.
or another instruction not
BCF, BSF
, etc.) on
EXAMPLE 5-3:
READ-MODIFY-WRITE
INSTRUCTIONS ON AN
I/O PORT
;Initial PORT settings: PORTB<7:4> Inputs
; PORTB<3:0> Outputs
;PORTB<7:6> have external pull-ups and are
;not connected to other circuitry
;
; PORT latch PORT pins
; ---------- ---------
BCF PORTB, 7 ; 01pp ppp 11pp ppp
BCF PORTB, 6 ; 10pp ppp 11pp ppp
BSF STATUS, RP0 ;
BCF TRISB, 7 ; 10pp ppp 11pp ppp
BCF TRISB, 6 ; 10pp ppp 10pp ppp
;
;Note that the user may have expected the
;pin values to be 00pp ppp. The 2nd BCF
;caused RB7 to be latched as the pin value
;(high).
FIGURE 5-5:
SUCCESSIVE I/O OPERATION
PC
PC + 1
PC + 2
PC + 3
Q1
Q2
Q3 Q4
Q1
Q2
Q3 Q4 Q1
Q2
Q3 Q4
Q1
Q2
Q3 Q4
Instruction
fetched
RB7:RB0
MOVWF PORTB
write to
PORTB
NOP
Port pin
sampled here
NOP
MOVF PORTB,W
Instruction
executed
MOVWF PORTB
write to
PORTB
NOP
NOP
MOVF PORTB,W
Note:
This example shows as write to PORTB
followed by a read from PORTB.
Note that:
data setup time = (0.25 T
CY
- T
PD
)
where:T
CY
= instruction cycle
T
PD
= propagation delay
Therefore, at higher clock frequencies, a write
followed by a read may be problematic.
相關PDF資料
PDF描述
PIC16F84 18-pin Flash/EEPROM 8-Bit Microcontrollers
PIC16F85 18/20 Pin, 8-Bit CMOS FLASH Microcontroller with Comparators and A/D Product Brief
PIC16F86 18/20 Pin, 8-Bit CMOS FLASH Microcontroller with Comparators and A/D Product Brief
PIC16F873A 28/40-pin Enhanced FLASH Microcontrollers
PIC16F874A 28/40-pin Enhanced FLASH Microcontrollers
相關代理商/技術參數
參數描述
PIC16F83-04/P 功能描述:8位微控制器 -MCU .875KB 36 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16F83-04/P 制造商:Microchip Technology Inc 功能描述:IC 8-BIT FLASH MCU
PIC16F83-04/SO 功能描述:8位微控制器 -MCU .875KB 36 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16F83-04I/P 功能描述:8位微控制器 -MCU .875KB 36 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16F83-04I/SO 功能描述:8位微控制器 -MCU .875KB 36 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*