參數資料
型號: PIC16F84-10/SO
廠商: Microchip Technology
文件頁數: 10/80頁
文件大小: 0K
描述: IC MCU FLASH 1KX14 EE 18SOIC
產品培訓模塊: Asynchronous Stimulus
8-bit PIC® Microcontroller Portfolio
標準包裝: 42
系列: PIC® 16F
核心處理器: PIC
芯體尺寸: 8-位
速度: 10MHz
外圍設備: POR,WDT
輸入/輸出數: 13
程序存儲器容量: 1.75KB(1K x 14)
程序存儲器類型: 閃存
EEPROM 大小: 64 x 8
RAM 容量: 68 x 8
電壓 - 電源 (Vcc/Vdd): 4 V ~ 6 V
振蕩器型: 外部
工作溫度: 0°C ~ 70°C
封裝/外殼: 18-SOIC(0.295",7.50mm 寬)
包裝: 管件
配用: XLT18SO-1-ND - SOCKET TRANSITION 18SOIC 300MIL
309-1075-ND - ADAPTER 18-SOIC TO 18-SOIC
309-1011-ND - ADAPTER 18-SOIC TO 18-DIP
309-1010-ND - ADAPTER 18-SOIC TO 18-DIP
AC164010-ND - MODULE SKT PROMATEII DIP/SOIC
PIC16F8X
DS30430C-page 18
1998 Microchip Technology Inc.
4.3
Program Counter: PCL and PCLATH
The Program Counter (PC) is 13-bits wide. The low
byte is the PCL register, which is a readable and
writable register. The high byte of the PC (PC<12:8>) is
not directly readable nor writable and comes from the
PCLATH register. The PCLATH (PC latch high) register
is a holding register for PC<12:8>. The contents of
PCLATH are transferred to the upper byte of the
program counter when the PC is loaded with a new
value. This occurs during a CALL, GOTO or a write to
PCL. The high bits of PC are loaded from PCLATH as
shown in Figure 4-1.
FIGURE 4-1:
LOADING OF PC IN
DIFFERENT SITUATIONS
4.3.1
COMPUTED GOTO
A computed GOTO is accomplished by adding an offset
to the program counter (ADDWF PCL). When doing a
table read using a computed GOTO method, care should
be exercised if the table location crosses a PCL memory
boundary (each 256 word block). Refer to the application
note
“Implementing a Table Read” (AN556).
4.3.2
PROGRAM MEMORY PAGING
The PIC16F83 and PIC16CR83 have 512 words of pro-
gram memory. The PIC16F84 and PIC16CR84 have
1K of program memory. The CALL and GOTO instruc-
tions have an 11-bit address range. This 11-bit address
range allows a branch within a 2K program memory
page size. For future PIC16F8X program memory
expansion, there must be another two bits to specify
the program memory page. These paging bits come
from the PCLATH<4:3> bits (Figure 4-1). When doing a
CALL
or a GOTO instruction, the user must ensure that
these page bits (PCLATH<4:3>) are programmed to
the desired program memory page. If a CALL instruc-
tion (or interrupt) is executed, the entire 13-bit PC is
“pushed” onto the stack (see next section). Therefore,
manipulation of the PCLATH<4:3> is not required for
the return instructions (which “pops” the PC from the
stack).
4.4
Stack
The PIC16FXX has an 8 deep x 13-bit wide hardware
stack (Figure 4-1). The stack space is not part of either
program or data space and the stack pointer is not
readable or writable.
The entire 13-bit PC is “pushed” onto the stack when a
CALL
instruction is executed or an interrupt is acknowl-
edged. The stack is “popped” in the event of a
RETURN,
RETLW
or a RETFIE instruction execution.
PCLATH is not affected by a push or a pop operation.
The stack operates as a circular buffer. That is, after the
stack has been pushed eight times, the ninth push over-
writes the value that was stored from the first push. The
tenth push overwrites the second push (and so on).
If the stack is effectively popped nine times, the PC
value is the same as the value from the first pop.
PC
12
8 7
0
5
PCLATH<4:0>
PCLATH
INST with PCL
as dest
ALU result
GOTO, CALL
Opcode <10:0>
8
PC
12 11 10
0
11
PCLATH<4:3>
PCH
PCL
87
2
PCLATH
PCH
PCL
Note:
The PIC16F8X ignores the PCLATH<4:3>
bits, which are used for program memory
pages 1, 2 and 3 (0800h - 1FFFh). The
use of PCLATH<4:3> as general purpose
R/W bits is not recommended since this
may affect upward compatibility with
future products.
Note:
There are no instruction mnemonics
called push or pop. These are actions that
occur from the execution of the CALL,
RETURN,
RETLW,
and RETFIE instruc-
tions, or the vectoring to an interrupt
address.
Note:
There are no status bits to indicate stack
overflow or stack underflow conditions.
相關PDF資料
PDF描述
AT91SAM7XC128-CU MCU ARM 128K HS FLASH 100-TFBGA
PIC18F2458-I/SO IC PIC MCU FLASH 12KX16 28SOIC
PIC18F4455-I/P IC PIC MCU FLASH 12KX16 40DIP
AT91SAM7X256-CU MCU ARM 256K HS FLASH 100-TFBGA
PIC16C73B-20/SS IC MCU OTP 4KX14 A/D PWM 28SSOP
相關代理商/技術參數
參數描述
PIC16F84A-04/P 功能描述:8位微控制器 -MCU 1.75KB 68 RAM 13 I/O 4MHz PDIP18 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16F84A-04/P 制造商:Microchip Technology Inc 功能描述:IC 8BIT FLASH MCU 16F84 DIP18
PIC16F84A-04/P 制造商:Microchip Technology Inc 功能描述:MICROCONTROLLER IC NUMBER OF I/OS:13 制造商:Microchip Technology Inc 功能描述:IC, 8BIT MCU, PIC16F, 4MHz, DIP-18
PIC16F84A-04/SO 功能描述:8位微控制器 -MCU 1.75KB 68 RAM 13 I/O 4MHz SOIC18 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16F84A-04/SO 制造商:Microchip Technology Inc 功能描述:8BIT FLASH MCU SMD 16F84 SOIC18