- 您現在的位置：買賣IC網 > PDF目錄3854 > PIC18F65K22-I/MR (Microchip Technology)IC MCU 8BIT 32KB FLASH 64QFN PDF資料下載
參數資料
| 型號： | PIC18F65K22-I/MR |
| 廠商： | Microchip Technology |
| 文件頁數： | 29/61頁 |
| 文件大小： | 0K |
| 描述： | IC MCU 8BIT 32KB FLASH 64QFN |
| 產品培訓模塊： | 8-bit PIC® Microcontroller Portfolio |
| 標準包裝： | 40 |
| 系列： | PIC® XLP™ 18F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 64MHz |
| 連通性： | I²C，LIN，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，LVD，POR，PWM，WDT |
| 輸入/輸出數： | 53 |
| 程序存儲器容量： | 32KB（16K x 16） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 1K x 8 |
| RAM 容量： | 2K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.8 V ~ 5.5 V |
| 數據轉換器： | A/D 16x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 64-VFQFN 裸露焊盤 |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
P89V52X2_3
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 4 May 2009
35 of 57
NXP Semiconductors
P89V52X2
80C51 with 256 B RAM, 192 B data EEPROM
Map the data EEPROM into code memory space if not already mapped.
Write the data EEPROM byte address into the DPTR.
Use the MOVC instruction to read the data EEPROM.
6.13.5 Erasing a complete page (64 B)
A complete page can be erased by performing the following sequence:
Map the data EEPROM into code memory space if not already mapped.
Write the lower 8-bits of the data EEPROM page’s start address into FMADRL.
Write the ERS_DP command (33H) to FMCON.
Once the ERS_DP command is written to FMCON, code execution will stall until the
operation is completed, approximately 6 ms.
6.13.6 Data EEPROM programming and erasing using the page register
In addition to page erase, a 64 B page register is included which allows from 1 B to 64 B
of a given page to be programmed or erase/programmed at the same time, substantially
reducing overall programming time. Two programming operations are provided:
Program only operation. This operation used the PROG (48H) command and
programs the contents of the page register into the data EEPROM page. This
operation requires that the bytes being programmed have been previously erased.
This operation requires approximately 2 ms to complete.
Erase and Program operation. This operation uses the EP (68H) command to both
erase and program the bytes previously loaded into the page register. This command
is often useful to erase and reprogram a single byte of data. This operation requires
approximately 4 ms to complete.
The page register consists of 64 B and an update ag for each byte. When a LOAD
command is issued to FMCON the page register contents and all of the update ags will
be cleared. When FMDATA is written, the value written to FMDATA will be stored in the
page register at the location specied by the lower 6 bits of FMADRL. In addition, the
update ag for that location will be set. FMADRL will auto-increment to the next location.
Auto-increment after writing to the last byte in the page register will ‘wrap-around’ to the
rst byte in the page register, but will not affect FMADRL[7:6]. Bytes loaded into the page
register do not have to be continuous. Any byte location can be loaded into the page
register by changing the contents of FMADRL prior to writing to FMDATA. However, each
location in the page register can only be written once following each LOAD command.
Attempts to write to a page register location more than once should be avoided.
FMADRH and FMADRL[7:6] are used to specify a page in the code memory space. When
the PROG command is written to FMCON, the locations within the data EEPROM page
that correspond to updated locations in the page register will have their contents
programmed with the contents of their corresponding locations in the page register. Only
the bytes that were loaded into the page register will be programmed in the data EEPROM
array. Other bytes within the data EEPROM array will not be affected. The EP command
works similarly except that If the EP command is written, the corresponding bytes in the
data EEPROM will be erased prior to being programmed. This is often useful for erasing
and programming a small number of bytes or even a single byte.
相關PDF資料 |
PDF描述 |
|---|---|
| 14FMN-BMTTR-A-TB | CONN FMN HSNG 14POS STAG REV SMD |
| 13FMN-BMTTR-A-TB | CONN FMN HSNG 13POS STAG REV SMD |
| 12FMN-BMTTR-A-TB | CONN FMN HSNG 12POS STAG REV SMD |
| ATMEGA8515-16MI | IC AVR MCU 8K 16MHZ IND 44-QFN |
| 10FMN-BMTTR-A-TB | CONN FMN HSNG 10POS STAG REV SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC18F65K22T-E/PT | 制造商:Microchip Technology Inc 功能描述:32KB FLASH, 2KB RAM, 1KB EE, NANOWATT XLP, GP - Tape and Reel 制造商:Microchip Technology Inc 功能描述:IC MCU 8BIT 32KB FLASH 64TQFP 制造商:Microchip Technology Inc 功能描述:32kB Flash, 2kB RAM, 1kB EE, nanoWatt XLP, GP, 64 TQFP 10x10x1mm T/R |
| PIC18F65K22T-I/MR | 功能描述:8位微控制器 -MCU 32kB Flash 2kB RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18F65K22T-I/MRRSL | 功能描述:8位微控制器 -MCU 32KB Flash 2KB RAM nanoWatt XLP GP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18F65K22T-I/PT | 功能描述:8位微控制器 -MCU 32kB Flash 2kB RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18F65K22T-I/PTRSL | 功能描述:8位微控制器 -MCU 32KB Flash 2KB RAM nanoWatt XLP GP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。