參數資料
型號: PIC18F8622T-I/PT
廠商: Microchip Technology
文件頁數: 4/10頁
文件大?。?/td> 0K
描述: IC PIC MCU FLASH 32KX16 80-TQFP
產品培訓模塊: Asynchronous Stimulus
PIC18 J Series MCU Overview
8-bit PIC® Microcontroller Portfolio
標準包裝: 1,200
系列: PIC® 18F
核心處理器: PIC
芯體尺寸: 8-位
速度: 40MHz
連通性: EBI/EMI,I²C,SPI,UART/USART
外圍設備: 欠壓檢測/復位,HLVD,POR,PWM,WDT
輸入/輸出數: 70
程序存儲器容量: 64KB(32K x 16)
程序存儲器類型: 閃存
EEPROM 大小: 1K x 8
RAM 容量: 3.8K x 8
電壓 - 電源 (Vcc/Vdd): 4.2 V ~ 5.5 V
數據轉換器: A/D 16x10b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 80-TQFP
包裝: 帶卷 (TR)
產品目錄頁面: 644 (CN2011-ZH PDF)
配用: XLT80PT3-ND - SOCKET TRAN ICE 80MQFP/TQFP
AC164320-ND - MODULE SKT MPLAB PM3 80TQFP
AC174011-ND - MODULE SKT PROMATEII 80TQFP
其它名稱: PIC18F8622T-I/PT-ND
PIC18F8622T-I/PTTR
2006 Microchip Technology Inc.
DS80253B-page 3
PIC18F6527/6622/8527/8622
10. Module: EUSART
In rare situations, one or more extra zero bytes
have been observed in a packet transmitted by the
module operating in Asynchronous mode. The
actual data is not lost or corrupted; only unwanted
(extra) zero bytes are observed in the packet.
This situation has only been observed when the
contents of the transmit buffer, TXREGx, are trans-
ferred to the TSRx during the transmission of a
Stop bit. For this to occur, three things must
happen in the same instruction cycle:
TXREGx is written to;
the baud rate counter overflows (at the end of
the bit period); and
a Stop bit is being transmitted (shifted out of
TSRx).
Work around
If possible, do not use the module’s double buffer
capability. Instead, load the TXREGx register
when the TRMT bit (TXSTAx<1>) is set, indicating
the TSRx is empty.
If double-buffering is used and back-to-back
transmission is performed, then load TXREGx
immediately after TXxIF is set or wait 1-bit time after
TXxIF is set. Both solutions prevent writing TXREGx
while a Stop bit is transmitted. Note that TXxIF is set
at the beginning of the Stop bit transmission.
11. Module: EUSART
When performing back-to-back transmission in 9-bit
mode (TX9D bit in the TXSTAx register is set), the
second byte may be corrupted if it is written into
TXREGx immediately after the TMRT bit is set.
Work around
Execute a software delay, at least one-half the
transmission’s bit time, after TMRT is set and prior
to writing subsequent bytes into TXREGx.
Date Codes that pertain to this issue:
All engineering and production devices.
If transmission is intermittent, then do the following:
Wait for the TRMT bit to be set before
loading TXREGx
Alternatively, use a free timer resource to time
the baud period. Set up the timer to overflow
at the end of the Stop bit, then start the timer
when you load the TXREGx. Do not load the
TXREGx when timer is about to overflow.
Date Codes that pertain to this issue:
All engineering and production devices.
12. Module: EUSART
With the auto-wake-up option enabled by setting
the WUE (BAUDCONx<1>) bit, the RCxIF bit will
become set on a high-to-low transition on the RXx
pin. However, the WUE bit may not clear within
1TCY of a low-to-high transition on RXx. While the
WUE bit is set, reading the receive buffer,
RCREGx, will not clear the RCxIF interrupt flag.
Therefore, the first opportunity to automatically
clear RCxIF by reading RCREGx may take longer
than expected.
Work around
There are two work arounds available:
1. Clear the WUE bit in software, after the wake-
up event has occurred, prior to reading the
receive buffer, RCREGx.
2. Poll the WUE bit and read RCREGx after the
WUE bit is automatically cleared.
Date Codes that pertain to this issue:
All engineering and production devices.
13. Module: MSSP (SPI Mode)
In SPI mode, the SDOx output may change after
the inactive clock edge of the bit ‘0’ output. This
may affect some SPI components that read data
over 300 ns after the inactive edge of SCKx.
Work around
None
Date Codes that pertain to this issue:
All engineering and production devices.
Note:
RCxIF can only be cleared by reading
RCREGx.
相關PDF資料
PDF描述
EP7311-IB IC ARM720T MCU 74MHZ 256-PBGA
EP7311-CV-90 IC ARM720T MCU 90MHZ 208-LQFP
EP7311-CV IC ARM720T MCU 74MHZ 208-LQFP
PIC24HJ128GP206-I/PT IC PIC MCU FLASH 128KB 64TQFP
PIC16F767-I/SS IC PIC MCU FLASH 8KX14 28SSOP
相關代理商/技術參數
參數描述
PIC18F8625-I/PT 功能描述:8位微控制器 -MCU 96kBF 4096RM 40MHz nonoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F8625T-I/PT 功能描述:8位微控制器 -MCU 96kBF 4096RM 40MHz nonoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F8627-E/PT 功能描述:8位微控制器 -MCU 96 KB FL 3936 RAM 25 MHz RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F8627-I/PT 功能描述:8位微控制器 -MCU 96 KB 4K RAM 70 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F8627T-E/PT 功能描述:8位微控制器 -MCU 96 KB 3936 RAM 25 MHz RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT