參數資料
型號： PIC18F86J65-I/PT
廠商： Microchip Technology
文件頁數： 3/8頁
文件大?。?/td> 0K
描述： IC PIC MCU FLASH 48KX16 80TQFP
產品培訓模塊： Asynchronous Stimulus
PIC18 J Series MCU Overview
8-bit PIC® Microcontroller Portfolio
標準包裝： 119
系列： PIC® 18F
核心處理器： PIC
芯體尺寸： 8-位
速度： 41.667MHz
連通性： 以太網，I²C，SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 55
程序存儲器容量： 96KB（48K x 16）
程序存儲器類型： 閃存
RAM 容量： 3808 x 8
電壓 - 電源 (Vcc/Vdd)： 2 V ~ 3.6 V
數據轉換器： A/D 15x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 80-TQFP
包裝： 托盤
產品目錄頁面： 645 (CN2011-ZH PDF)
配用： AC162064-ND - HEADER INTFC MPLABICD2 64/80/100
AC164328-ND - MODULE SKT FOR 80TQFP
2008 Microchip Technology Inc.
DS80292D-page 3
PIC18F97J60 FAMILY
5.
Module: Ethernet (MIIM)
When writing to any PHY register through the MIIM
interface’s MIWRL and MIWRH registers, the low
byte actually written to the PHY register may be
corrupted. The corruption occurs when the
following actions are taken:
The application writes to MIWRL
The PIC MCU core executes any instruction
that reads or writes to any memory address that
has the Least Significant six address bits of 36h
(‘b110110)
The application writes to MIWRH
For example, the following sequence will result in
a corrupted write to a PHY register:
In this example, 0xCF5 and 0xCF6 are GPR
memory locations that the application wishes to
write to the current PHY register defined by the
MIREGADR SFR. When the PIC MCU core
reads from
the
GPR
at
address
0xCF6
(‘b110011110110), the value originally written to
MIWRL will be corrupted.
Work around 1
Ensure that following a write to MIWRL, the firm-
ware does not access any of the problem memory
locations prior to writing to MIWRH. After finished
writing to MIWRH, normal operation can resume.
If interrupts are enabled, disable them prior to writ-
ing to MIWRL and MIWRH to prevent an Interrupt
Service Routine (ISR) from performing any reads
or writes to a problem memory address.
Special care must be taken to ensure that the
source data to be written to MIWRH does not
result in a problem memory access.
The following PHY write sequence avoids the
problem:
1. Copy the low byte, to be written to the PHY, into
the PRODL register.
PRODL is at address FF3h and not subject to
the memory address issue.
2. Copy the high byte, to be written to the PHY,
into the PRODH register.
PRODH is at address FF4h and not subject to
the memory address issue.
3. Disable all interrupts by clearing GIEH and
GIEL in the INTCON register.
4. Move PRODL into MIWRL.
5. Wait one instruction cycle, as required by the
MAC host interface logic.
6. Move PRODH into MIWRH.
7. Enable all interrupts that are needed by
restoring GIEH and GIEL in INTCON.
Work around 2
If you cannot disable interrupts, as specified in
Work around 1, because the application cannot
tolerate interrupt latency variations:
Perform the write (with interrupts enabled), but
Verify the correct values were written by
reading the PHY register
If a corrupted value was written due to an interrupt
occurring, perform the write again and reverify.
The source data must be stored in a non-problem
location.
The
application
should
follow
the
following
procedure:
1. Copy the low byte, to be written to the PHY, into
the PRODL register.
PRODL is at address FF3h and not subject to
the memory address issue.
2. Copy the high byte, to be written to the PHY,
into the PRODH register.
PRODH is at address FF4h and not subject to
the memory address issue.
3. Move PRODL into MIWRL.
4. Wait one instruction cycle, as required by the
MAC host interface logic.
5. Move PRODH into MIWRH.
6. Wait two TCY and then poll the BUSY bit
(MISTAT<0>) until it is clear.
7. Perform a PHY register read of the same
location.
8. Compare the read result with the original value
copied to the PRODH:PRODL registers. If they
do not match, return to step 1.
Date Codes that pertain to this issue:
All engineering and production devices.
6.
Module: Ethernet (RX Filter)
When enabled, the Pattern Match receive filter
may allow some packets with an incorrect data
pattern to be received. Also, in certain configura-
tions, packets with a valid pattern may be
incorrectly discarded.
Work around
Do not use the Pattern Match hardware filter.
Instead, use the Unicast, Mutlicast, Broadcast and
Hash Table receive filters to accept all needed
packets and filter out unwanted ones in software.
Date Codes that pertain to this issue:
All engineering and production devices.
MOVFF
0xCF5, MIWRL
NOP
MOVFF
0xCF6, MIWRH
相關PDF資料
PDF描述
PIC32MX320F064H-40I/MR IC PIC MCU FLASH 64KB 64-QFN
PIC18F4423-I/P IC PIC MCU FLASH 8KX16 40DIP
PIC18LF8390-I/PT IC PIC MCU FLASH 4KX16 80TQFP
PIC18F2455-I/SO IC PIC MCU FLASH 12KX16 28SOIC
TS87C51RD2-VCL IC MCU 8051 OTP 64K 5V 68PLCC
相關代理商/技術參數
參數描述
PIC18F86J65T-I/PT 功能描述:8位微控制器 -MCU 96KB FL 12KB RAM 10BASE-T RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F86J72-I/PT 功能描述:8位微控制器 -MCU Energy Meter 64KB LCD, CTMU, RTCC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F86J72T-I/PT 功能描述:8位微控制器 -MCU Energy Meter 64KB LCD, CTMU, RTCC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F86J90-I/PT 功能描述:8位微控制器 -MCU Segmnt LCD 96KBFlash 4KBRAM 12MIPS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F86J90T-I/PT 功能描述:8位微控制器 -MCU Segmnt LCD 96KBFlash 4KBRAM 12MIPS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*