- 您現在的位置：買賣IC網 > PDF目錄3846 > PIC18F86J90-I/PT (Microchip Technology)IC PIC MCU FLASH 64KB 80-TQFP PDF資料下載
參數資料
| 型號： | PIC18F86J90-I/PT |
| 廠商： | Microchip Technology |
| 文件頁數： | 27/59頁 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 64KB 80-TQFP |
| 產品培訓模塊： | PIC18 J Series MCU Overview 8-bit PIC® Microcontroller Portfolio |
| 標準包裝： | 119 |
| 系列： | PIC® 18F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 48MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，LCD，LVD，POR，PWM，WDT |
| 輸入/輸出數： | 67 |
| 程序存儲器容量： | 64KB（32K x 16） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 3.8K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2 V ~ 3.6 V |
| 數據轉換器： | A/D 12x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 80-TQFP |
| 包裝： | 托盤 |
| 產品目錄頁面： | 644 (CN2011-ZH PDF) |
| 配用： | AC162079-ND - HEADER MPLAB ICD2 18F85J90 64/80 AC164328-ND - MODULE SKT FOR 80TQFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
2010 Microchip Technology Inc.
DS39933D-page 33
PIC18F87J90 FAMILY
2.4
Voltage Regulator Pins (ENVREG
and VCAP/VDDCORE)
The on-chip voltage regulator enable pin, ENVREG,
must always be connected directly to either a supply
voltage or to ground. Tying ENVREG to VDD enables
the regulator, while tying it to ground disables the
regulator. Refer to Section 25.3 “On-Chip Voltage
Regulator” for details on connecting and using the
on-chip regulator.
When the regulator is enabled, a low-ESR (< 5)
capacitor is required on the VCAP/VDDCORE pin to
stabilize the voltage regulator output voltage. The
VCAP/VDDCORE pin must not be connected to VDD and
must use a capacitor of 10
F connected to ground. The
type can be ceramic or tantalum. A suitable example is
the Murata GRM21BF50J106ZE01 (10
F, 6.3V) or
equivalent. Designers may use Figure 2-3 to evaluate
ESR equivalence of candidate devices.
It is recommended that the trace length not exceed
0.25 inch (6 mm). Refer to Section 28.0 “Electrical
Characteristics” for additional information.
When the regulator is disabled, the VCAP/VDDCORE pin
must be tied to a voltage supply at the VDDCORE level.
Refer to Section 28.0 “Electrical Characteristics” for
information on VDD and VDDCORE.
Note that the “LF” versions of some low pin count
PIC18FJ parts (e.g., the PIC18LF45J10) do not have
the ENVREG pin. These devices are provided with the
voltage regulator permanently disabled; they must
always be provided with a supply voltage on the
VDDCORE pin.
FIGURE 2-3:
FREQUENCY vs. ESR
PERFORMANCE FOR
SUGGESTED VCAP
2.5
ICSP Pins
The PGC and PGD pins are used for In-Circuit Serial
Programming (ICSP) and debugging purposes. It
is recommended to keep the trace length between the
ICSP connector and the ICSP pins on the device as
short as possible. If the ICSP connector is expected to
experience an ESD event, a series resistor is recom-
mended, with the value in the range of a few tens of
ohms, not to exceed 100.
Pull-up resistors, series diodes, and capacitors on the
PGC and PGD pins are not recommended as they will
interfere with the programmer/debugger communica-
tions to the device. If such discrete components are an
application requirement, they should be removed from
the circuit during programming and debugging. Alter-
natively, refer to the AC/DC characteristics and timing
requirements information in the respective device
Flash programming specification for information on
capacitive loading limits, and pin input voltage high
(VIH) and input low (VIL) requirements.
For device emulation, ensure that the “Communication
Channel Select” (i.e., PGCx/PGDx pins) programmed
into the device matches the physical connections for
the ICSP to the Microchip debugger/emulator tool.
For
more
information
on
available
Microchip
development tools connection requirements, refer
10
1
0.1
0.01
0.001
0.01
0.1
1
10
100
1000 10,000
Frequency (MHz)
ES
R
(
)
Note:
Data for Murata GRM21BF50J106ZE01 shown.
Measurements at 25°C, 0V DC bias.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC32MX150F128D-I/PT | IC MCU 32BIT 128KB FLASH 44-TQFP |
| PIC24EP64MC206-I/PT | MCU 16BIT 64KB FLASH 64TQFP |
| DSPIC33EP64MC206-I/PT | IC DSC 16BIT 64KB FLASH 64TQFP |
| PIC24EP64GP206-I/PT | MCU 16BIT 64KB FLASH 64TQFP |
| ATTINY13V-10PJ | IC MCU AVR 1K 5V 10MHZ 8DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC18F86J90T-I/PT | 功能描述:8位微控制器 -MCU Segmnt LCD 96KBFlash 4KBRAM 12MIPS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18F86J93-I/PT | 功能描述:8位微控制器 -MCU 80pin,4KB RAM,12MIPS SEG LCD, 64KB Flash RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18F86J93T-I/PT | 功能描述:8位微控制器 -MCU 80pin,4KB RAM,12MIPS SEG LCD, 64KB Flash RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18F86J94-I/PT | 制造商:Microchip Technology Inc 功能描述:80 PINS, 64KB FLASH, 4KB RAM, 16MIPS, NANOWATT XLP, LCD, USB - Trays 制造商:Microchip Technology Inc 功能描述:IC MCU 8BIT 64KB FLASH 80TQFP |
| PIC18F86J94T-I/PT | 制造商:Microchip Technology Inc 功能描述:80 PINS, 64KB FLASH, 4KB RAM, 16MIPS, NANOWATT XLP, LCD, USB - Tape and Reel 制造商:Microchip Technology Inc 功能描述:IC MCU 8BIT 64KB FLASH 80TQFP 制造商:Microchip Technology Inc 功能描述:8-bit Microcontrollers - MCU 80 pins, 64KB Flash, 4KB RAM, 16MIPS |
發布緊急采購，3分鐘左右您將得到回復。