參數資料
型號： PIC18F86K22-I/PTRSL
廠商： Microchip Technology
文件頁數： 29/61頁
文件大小： 0K
描述： MCU PIC 64K FLASH XLP 80TQFP
產品培訓模塊： 8-bit PIC® Microcontroller Portfolio
標準包裝： 119
系列： PIC® XLP™ 18F
核心處理器： PIC
芯體尺寸： 8-位
速度： 64MHz
連通性： EBI/EMI，I²C，LIN，SPI，UART/USART
外圍設備： 欠壓檢測/復位，LVD，POR，PWM，WDT
輸入/輸出數： 69
程序存儲器容量： 64KB（32K x 16）
程序存儲器類型： 閃存
EEPROM 大小： 1K x 8
RAM 容量： 4K x 8
電壓 - 電源 (Vcc/Vdd)： 1.8 V ~ 5.5 V
數據轉換器： A/D 24x12b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 80-TQFP
包裝： 托盤
P89V52X2_3
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 4 May 2009
35 of 57
NXP Semiconductors
P89V52X2
80C51 with 256 B RAM, 192 B data EEPROM
Map the data EEPROM into code memory space if not already mapped.
Write the data EEPROM byte address into the DPTR.
Use the MOVC instruction to read the data EEPROM.
6.13.5 Erasing a complete page (64 B)
A complete page can be erased by performing the following sequence:
Map the data EEPROM into code memory space if not already mapped.
Write the lower 8-bits of the data EEPROM page’s start address into FMADRL.
Write the ERS_DP command (33H) to FMCON.
Once the ERS_DP command is written to FMCON, code execution will stall until the
operation is completed, approximately 6 ms.
6.13.6 Data EEPROM programming and erasing using the page register
In addition to page erase, a 64 B page register is included which allows from 1 B to 64 B
of a given page to be programmed or erase/programmed at the same time, substantially
reducing overall programming time. Two programming operations are provided:
Program only operation. This operation used the PROG (48H) command and
programs the contents of the page register into the data EEPROM page. This
operation requires that the bytes being programmed have been previously erased.
This operation requires approximately 2 ms to complete.
Erase and Program operation. This operation uses the EP (68H) command to both
erase and program the bytes previously loaded into the page register. This command
is often useful to erase and reprogram a single byte of data. This operation requires
approximately 4 ms to complete.
The page register consists of 64 B and an update ag for each byte. When a LOAD
command is issued to FMCON the page register contents and all of the update ags will
be cleared. When FMDATA is written, the value written to FMDATA will be stored in the
page register at the location specied by the lower 6 bits of FMADRL. In addition, the
update ag for that location will be set. FMADRL will auto-increment to the next location.
Auto-increment after writing to the last byte in the page register will ‘wrap-around’ to the
rst byte in the page register, but will not affect FMADRL[7:6]. Bytes loaded into the page
register do not have to be continuous. Any byte location can be loaded into the page
register by changing the contents of FMADRL prior to writing to FMDATA. However, each
location in the page register can only be written once following each LOAD command.
Attempts to write to a page register location more than once should be avoided.
FMADRH and FMADRL[7:6] are used to specify a page in the code memory space. When
the PROG command is written to FMCON, the locations within the data EEPROM page
that correspond to updated locations in the page register will have their contents
programmed with the contents of their corresponding locations in the page register. Only
the bytes that were loaded into the page register will be programmed in the data EEPROM
array. Other bytes within the data EEPROM array will not be affected. The EP command
works similarly except that If the EP command is written, the corresponding bytes in the
data EEPROM will be erased prior to being programmed. This is often useful for erasing
and programming a small number of bytes or even a single byte.
相關PDF資料
PDF描述
PIC16C63A-04I/SP IC MCU OTP 4KX14 PWM 28DIP
PIC16C63A-04I/SO IC MCU OTP 4KX14 PWM 28SOIC
52559-2270 CONN FFC 22POS .5MM VERT ZIF SMD
52559-1870 CONN FFC 18POS .5MM VERT ZIF SMD
DSPIC33EP64MC506-I/PT IC DSC 16BIT 64KB FLASH 64TQFP
相關代理商/技術參數
參數描述
PIC18F86K22T-I/PT 功能描述:8位微控制器 -MCU 64kB Flash 4kB RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F86K22T-I/PTRSL 功能描述:8位微控制器 -MCU 64KB Flash 4KB RAM nanoWatt XLP GP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F86K90-E/PT 功能描述:8位微控制器 -MCU 64KB Flash 4KB RAM LCD RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F86K90-I/PT 功能描述:8位微控制器 -MCU 64kB Flash 4kB RAM LCD RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F86K90-I/PTRSL 功能描述:8位微控制器 -MCU 64KB 4KB RAM 16MIPS nanoWatt XLP LCD 5V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*